Moxa Technologies Switch CSM 200 User Manual

CSM-200 Series  
Hardware Installation Guide  
First Edition, November 2009  
© 2009 Moxa Inc. All rights reserved.  
Reproduction without permission is prohibited.  
Fl.4, No.135, Lane 235, Pao-Chiao Rd. Shing Tien City,  
Taipei, Taiwan, R.O.C.  
TEL: +886-2-8919-1230  
P/N: 1802002002010  
 
Features  
y
LFP(Link Fault Pass-through) and FEF(Far End Fault)  
y
Two different operation modes  
¾
¾
Store-and-Forward  
Pass Through  
y
y
y
y
y
Auto negotiation  
Support TS-1000 ver. 2  
Support Turbo Ring 2  
Plug and Play  
Hot-swap  
Package Checklist  
Moxa’s CSM-200 Series is shipped with the following items. If any of these  
items is missing or damaged, please contact your customer service  
representative for assistance.  
y
y
y
CSM-200 Series  
Hardware Installation Guide  
Warranty Card  
NOTE: Please notify your sales representative if any of the above items are  
missing or damaged.  
Dimensions  
CSM-200-1213  
PWR  
Fiber  
Link  
TX  
RX  
86.8 mm  
10M  
(3.42 in)  
100M  
117.1 mm (4.61 in)  
124.3 mm (4.89 in)  
21 mm  
(0.83 in)  
- 3 -  
 
CSM-200-1214/CSM-200-1218  
PWR  
Fiber  
Link  
TX  
RX  
86.8 mm  
(3.42 in)  
10M  
100M  
117.1 mm (4.61 in)  
124.3 mm (4.89 in)  
21 mm  
(0.83 in)  
ATTENTION  
Electrostatic Discharge Warning!  
To protect the product from damage due to electrostatic  
discharge, we recommend wearing a grounding device when  
handling your CSM-200 slide-in modules.  
Communication Connections  
The CSM-200 Series has one 10/100BaseT(X) Ethernet port, and one  
100BaseFX (SC or ST type connector) fiber port.  
10/100BaseT(X) Ethernet Port Connection  
The 10/100BaseT(X) Ethernet ports located on CSM-200 are used to connect  
to Ethernet-enabled devices.  
Below we show pinouts for both MDI (NIC-type) ports and MDI-X  
(HUB/Switch-type) ports, and also show cable wiring diagrams for  
straight-through and cross-over Ethernet cables.  
RJ45 (8-pin, MDI) Port Pinouts  
RJ45 (8-pin, MDI-X) Port Pinouts  
Pin  
Signal  
Pin  
Signal  
1
2
3
6
Tx+  
Tx-  
Rx+  
Rx-  
1
2
3
6
Rx+  
Rx-  
Tx+  
Tx-  
1
8
1
8
- 4 -  
 
RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring  
Straight-Through Cable  
Switch Port  
NIC Port  
RJ45 Plug Pin 1  
Cable Wiring  
RJ45  
Connector  
RJ45  
Connector  
Tx+  
Tx-  
Rx+  
Rx-  
3
6
1
2
3
6
1
2
Rx+  
Rx-  
Tx+  
Tx-  
RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring  
Cross-Over Cable  
Switch Port  
(NIC Port)  
Switch Port  
(NIC Port)  
RJ45 Plug Pin 1  
RJ45  
RJ45  
Connector  
Cable Wiring  
Connector  
(Rx+) Tx+  
(Rx-) Tx-  
(Tx+) Rx+  
(Tx-) Rx-  
3
6
1
2
1
2
3
6
Rx+ (Tx+)  
Rx- (Tx-)  
Tx+ (Rx+)  
Tx- (Rx-)  
100BaseFX Fiber Port Connection  
The concept behind the SC port and cable is quite straightforward. Suppose  
you are connecting devices I and II. Contrary to electrical signals, optical  
signals do not require a circuit in order to transmit data. Consequently, one of  
the optical lines is used to transmit data from device I to device II, and the  
other optical line is used transmit data from device II to device I, for  
full-duplex transmission.  
All you need to remember is to connect the Tx (transmit) port of device I to the  
Rx (receive) port of device II, and the Rx (receive) port of device I to the Tx  
(transmit) port of device II. If you are making your own cable, we suggest  
labeling the two sides of the same line with the same letter (A-to-A and B-to-B,  
as shown below, or A1-to-A2 and B1-to-B2).  
SC-Port Pinouts  
SC-Port to SC-Port Cable Wiring  
A
B
A
B
Tx  
Cable Wiring  
Rx  
A
B
A
B
ST-Port Pinouts  
ST-Port to ST-Port Cable Wiring  
Cable Wiring  
A
B
A
B
Tx  
A
B
A
B
Rx  
- 5 -  
 
ATTENTION  
This is a Class 1 Laser/LED product. Do not stare into the  
Laser Beam.  
Switch Settings  
There is 1 set of DIP switches on the board. The following figure and table  
give the settings for the 5-connector DIP switch.  
DIP  
1
2
3
4
Function  
Auto Negotiation  
Force TP Speed  
Force TP Duplex  
Link Fault Pass Through Enable  
Operating Mode  
ON  
OFF  
Enable  
100 M  
Disable  
10 M  
Full Duplex  
Half Duplex  
Disable  
5
Store-and-Forward Pass Through  
1. All the DIP settings default to “ON”.  
NOTE  
2. When configured for Pass Through mode, the Ethernet port  
and fiber port should transmit at 100 Mbps, which is  
equivalent to full duplex mode.  
LED Indicators  
There are 2 LEDs on the front bracket of the CSM-200 slide-in modules.  
LED  
Color  
State  
Function  
On  
Power is being supplied to power input.  
PWR  
Green  
Power is not being supplied to power  
input.  
Off  
On  
FX port’s 100 Mbps is active.  
Fiber Link Green  
Blinking Data is being transmitted at 100 Mbps.  
Off  
On  
100BaseFX port is inactive.  
TP port’s 10 Mbps is active.  
10M (TP)  
Yellow  
Blinking Data is being transmitted at 10 Mbps.  
Off  
On  
TP port’s 10 Mbps link is inactive.  
TP port’s 100 Mbps is active.  
100M (TP) Green  
Blinking Data is being transmitted at 100 Mbps.  
Off  
TP Port’s 100 Mbps is inactive.  
- 6 -  
 
Auto MDI/MDI-X Connection  
The Auto MDI/MDI-X function allows users to connect the Moxa CSM-200’s  
10/100BaseTX ports to any kind of Ethernet device, without needing to  
determine the type of Ethernet cable being used for the connection.  
This means that you can use either a straight-through cable or cross-over cable  
to connect the CSM-200 Series to Ethernet devices.  
Dual Speed Functionality and  
Switching  
The Moxa CSM-200’s 10/100 Mbps RJ45 Ethernet port auto negotiates with  
the connected device for the fastest data transmission rate supported by both  
devices. All models of the CSM-200 Series are plug-and-play devices, so that  
software configuration is not required at installation, or during maintenance.  
The half/full duplex mode for the RJ45 Ethernet ports is user dependent and  
changes (by auto-negotiation) to full or half duplex, depending on which  
transmission speed is supported by the attached device.  
Auto-Negotiation and Speed Sensing  
All of the CSM-200’s RJ45 Ethernet ports independently support  
auto-negotiation for 10BaseT and 100BaseTX transmission speeds, with  
operation according to the IEEE 802.3u standard.  
This means that some nodes could be operating at 10 Mbps, while at the same  
time other nodes are operating at 100 Mbps.  
Auto-negotiation takes place when an RJ45 cable connection is made, and then  
each time a LINK is enabled. Moxa’s CSM-200 advertises its capability for  
using either 10 Mbps or 100 Mbps transmission speeds, with the device at the  
other end of the cable expected to advertise similarly. Depending on what type  
of device is connected, this will result in agreement to operate at a speed of  
either 10 Mbps or 100 Mbps.  
If a Moxa CSM-200 RJ45 Ethernet port is connected to a non-negotiating  
device, it will default to 10 Mbps speed and half-duplex mode, as required by  
the IEEE 802.3u standard.  
- 7 -  
 
Specifications  
Technology  
Standards  
IEEE 802.3 for 10BaseT,  
IEEE 802.3u for 100BaseT(X), 100BaseFX  
Interface  
RJ45 ports  
10/100BaseT(X)  
Fiber ports  
100BaseFX (SC/ST connector)  
PWR, Fiber Link, 10/100M(TP port)  
LED Indicators  
Optical Fiber  
100BaseFX  
Multi-mode Single-mode  
Wavelength  
Max. TX  
Min. TX  
RX Sensitivity  
Link Budget  
1300 nm  
-10 dBm  
-20 dBm  
-32 dBm  
12 dB  
1310 nm  
0 dBm  
-5 dBm  
-34 dBm  
29 dB  
5 km a  
4 km b  
-6 dBm  
Typical Distance  
Saturation  
40 km c  
-3 dBm  
a. 50/125 μm, 800 MHz*km fiber optic cable  
b. 62.5/125 μm, 500 MHz*km fiber optic cable  
c. 9/125 μm, 3.5 PS/(nm*km) fiber optic cable  
Physical Characteristics  
Housing  
Dimensions  
Weight  
SPCC  
86.8 x 124.3 x 21 mm (3.42 x 4.89 x 0.83 in)  
Product only:  
CSM-1213: 115 g (0.25 lb)  
CSM-1214/1218: 125 g (0.28 lb)  
Packaged:  
CSM-1213: 170g (0.37 lb)  
CSM-1214/1218: 180g (0.40 lb)  
Environmental Limits  
Operating Temperature  
Storage Temperature  
Humidity  
0 to 60°C (32 to 142°F)  
-20 to 75°C (-4 to 158°F)  
5 to 95 % RH  
Power Requirements  
Input Voltage  
12 VDC  
Power Consumption  
Regulatory Approvals  
CE  
180 mA @ 12 VDC  
Class A  
FCC  
Part 15 sub part B class A  
- 8 -  
 
EMS  
EN61000-4-2 (ESD), Criteria A, Level 4  
EN61000-4-3 (RS), Criteria A, Level 2  
EN61000-4-4 (EFT), Criteria A, Level 3  
EN61000-4-5 (Surge), Criteria A, Level 3  
EN61000-4-6 (CS), Criteria A, Level 2  
En61000-4-8 (PFMF), Criteria A, Level 3  
IEC 60068-2-32  
Freefall  
Warranty  
Warranty Period  
5 years  
Technical Support Contact Information  
Moxa Americas:  
Toll-free: 1-888-669-2872  
Moxa China (Shanghai office):  
Toll-free: 800-820-5036  
Tel:  
Fax:  
+1-714-528-6777  
+1-714-528-6778  
Tel:  
Fax:  
+86-21-5258-9955  
+86-10-6872-3958  
Moxa Europe:  
Moxa Asia-Pacific:  
Tel:  
Fax:  
+49-89-3 70 03 99-0  
+49-89-3 70 03 99-99  
Tel:  
Fax:  
+886-2-8919-1230  
+886-2-8919-1231  
 

Miele Cooktop KM89 2 User Manual
Milwaukee Drill 0375 1 User Manual
Nady Systems Speaker System PCS 12 User Manual
Nilfisk ALTO Pressure Washer Multi User Pressure Washer System User Manual
NuTone Fan 690NT User Manual
Olympus Camcorder TG 320 User Manual
Omega Vehicle Security Switch PSW490B User Manual
Optimus Home Theater System SYSTEM 730 User Manual
Panasonic Network Card EZACT User Manual
Panasonic Printer KX P7100 User Manual