To find out about individual chassis A and B
backplane links, refer to the specific chassis’ user
manual.
DIP-Switch is in the “OFF” position, the iConverter
10T/2 module’s A backplane Ethernet port will be isolated
from the backplane.
OVERVIEW:
to the slot on its left using the “A” link and to the slot on
its right using the “B” link.
The iConverter 10T/2 converter supports the IEEE
802.3 standard and converts 10BASE-T cabling (UTP)
to 10BASE-2 coax cabling. The iConverter supports
Half-Duplex 10Mbps Ethernet and provides a crossover
UTP switch for easy attachment to hubs, switches and
workstations. It also features a termination switch for
easy coax termination.
The 10T/2 can be used as a standard two-port UTP to
fiber converter. It can also use its two additional
10/100 backplane Ethernet ports to connect to adjacent
modules and accommodate flexible network
configurations like In-Band management and multi-
module configurations. The iConverter 19-Module,
5-Module or 2-Module Chassis have backplanes that
facilitate connectivity between adjacent modules.
®
In this example, the module on the left is an NMM and
it connects via its “A” link to the 10T/2 facilitating
In-Band management. The module on the right is an
iConverter 10/100 module and it connects via its “B”
link to the 10T/2 facilitating a 2-port 10/100 Ethernet
hub/switch with a 10BASE-2 port and a fiber uplink. This
3-module configuration provides an effective
10BASE-2 to 10/100 managed switch with a fiber uplink.
iConverter 10T/2 User Manual
Front Plane RJ45 Crossover “= / X” Switch:
Backplane B Enable “B-EN” DIP-Switch:
When connecting to a workstation, set this DIP-Switch
to Straight-Through “=” (factory setting). When
connecting to a hub or switch, set to Crossover “X”.
When the Backplane B Enable “B-EN” DIP-Switch is in
the “ON” position, the iConverter 10T/2 module’s B
backplane Ethernet port is enabled. This port allows
connectivity to adjacent modules and facilitates
In-Band management of the Network Management
Module (NMM). When the Backplane B Enable “B-EN”
DIP-Switch is in the “OFF” position, the iConverter
10T/2 module’s B backplane Ethernet port will be isolated
from the backplane.
BOARD MOUNTED DIP-SWITCH SETTINGS:
ON
“TST” DIP-Switch:
OFF
1
2
3
4
This switch is reserved for factory use, and should be
left in the “OFF” position.
The 10T/2 can be used in an unmanaged or managed
fashion. When unmanaged, it can be installed in a
chassis without a Network Management Module (NMM).
To be managed, a NMM module must be installed in the
same chassis.
Fig. 2 Board Mounted DIP-Switches
Coax Termination “T-IN” DIP-Switch:
Model Type
8340-0
Connectors
UTP
Distance
100m
When the Coax Termination “T-IN” DIP-Switch is in the
“ON” position, the coax port is terminated. Use this
DIP-Switch setting when this coax port is at the end of
the network.
Due to the Ethernet 5-4-3 rule, no more than
4 iConverter 10T/2 modules can be
linked together via the backplane buses.
Coax
185m
For wide temperature (-40 to 60º C) modules, add a "W" to the end
of the model number. Consult factory for other configurations and
extended temperature (-40 to +75º C) modules.
Backplane A Enable “A-EN” DIP-Switch:
Fig. 1 10T/2 Application Example
PORT STRUCTURE:
When the Backplane A Enable “A-EN” DIP-Switch is in
the “ON” position, the iConverter 10T/2 module’s “A”
backplane Ethernet port is enabled. This port allows
connectivity to adjacent modules and facilitates
In-Band management of the Network Management
Module (NMM). When the Backplane A Enable “A-EN”
Fig. 1 depicts a chassis with three modules plugged
into three of its adjacent backplane slots. The adjacent
slots are connected to the “A” and “B” backplane links
via the module’s “A” and “B” backplane Ethernet ports.
In this example, the 10T/2 in the center slot connects
This example shows how the 10T/2 can be used either
as a traditional managed or unmanaged media converter
or to create flexible and effective network hub/switch
configurations.
Page 1
Page 2
Page 3
Page 4
Page 5
Technical Support:
Warning
maintenance of the equipment by Buyer, Buyer-
supplied equipment, Buyer-supplied interfacing,
unauthorized modifications or tampering with equipment
(including repairs of equipment by personnel not
specifically authorized and certified by Omnitron), or
misuse, or operating outside the environmental
specification of the product (including but not limited
to voltage, ambient temperature, radiation, unusual
dust, etc.), or improper site preparation or maintenance.
MOUNTING AND CABLE ATTACHMENT:
iConverter modules are hot-swappable and can be
installed into any chassis in the iConverter family.
1. Carefully slide the iConverter module into the
installation slot, aligning the module with installation
guides, and secure using the front panel fastener
screw. NOTE: Ensure that module is firmly seated
against the backplane.
10T/2 SPECIFICATIONS:
For help with this product, contact our Technical Support:
The operating description in this Instruction Manual is
for use by qualified personnel only. To avoid electrical
shock, do not perform any servicing of this unit other
than that contained in the operating instructions, unless
you are qualified and certified to do so by Omnitron
Systems Technology, Inc.
Model Type
Protocols
10T/2
Phone:
Fax:
(949) 250-6510
(949) 250-6514
10BASE-T and 10BASE-2
RJ-45 and BNC
Address: Omnitron Systems Technology, Inc.
140 Technology Dr., #500
Connectors
Coax Termination,
Backplane Enables
Irvine, CA 92618 USA
Controls
Warranty
Email:
URL:
2. Secure module by securing panel fastener screw
(attached to module) to chassis front.
This product is warranted to the original purchaser
against defects in material and workmanship for a
period of 2 YEARS from the date of shipment. A
LIFETIME limited warranty may be obtained by the
original purchaser by REGISTERING this product with
Omnitron within 90 days from the date of shipment. To
register, complete and mail or fax the enclosed
Registration Card to the indicated address. You may
also register your product on the internet at
warranty period, Omnitron will, at its option, repair or
replace a product which is proven to be defective.
Power, Coax Collision,
Coax Activity, UTP Link/Activity
No other warranty is expressed or implied. Omnitron
specifically disclaims the implied warranties of
merchantability and fitness for any particular purpose.
LED Displays
3. Attach the iConverter 10T/2 RJ45 connector via a
category 5 cable to a 10Base-T Ethernet device.
Dimensions
Weight
W:0.85" x D:4.5" x H:2.8"
8 oz.
Exclusive Remedies
4. Attach the iConverter 10T/2, via a coax cable to a
10BASE-2 Ethernet device.
The remedies provided herein are the Buyer’s sole and
exclusive remedies. Omnitron shall not be liable for
any direct, indirect, special, incidental, or consequential
damages, whether based on contract, tort, or any legal
theory.
Compliance
UL, CE, FCC Class A
5. If using the iConverter 10T/2 at the end of a coaxial
network, set Coax Termination “T-IN” DIP-Switch to
the “ON” position.
Power
Requirement
1.0A @ 3.3VDC (typical)
Standard: 0 to 50º C
Wide: -40 to 60º C
Storage: -40 to 80º C
LED INDICATORS:
Temperature
LED
Color Description
For warranty service, the product must be sent to an
Omnitron designated facility, at Buyer’s expense.
Omnitron will pay the shipping charge to return the
product to Buyer’s designated US address (within the
48 contiguous states and the District of Columbia)
using Omnitron’s standard shipping method.
Pwr:
Col:
Act:
Lk/Act:
Yellow On - Power on
Yellow On - Coax collision
Green On - Coax activity
Green On - UTP link
Blink - UTP activity
Humidity
Altitude
5 to 95% (non-condensing)
-100m to 4000m
722,000
MTBF (hrs)
Limitation of Warranty
The foregoing warranty shall not apply to defects
resulting from improper or inadequate use and/or
Form: 040-08340-001D 9/07
Page 10
Page 6
Page 7
Page 8
Page 9
|