Sceptre Technologies Computer Monitor X9G NAGAV User Guide

X9G-NagaV  
X9S-NagaV  
User’s Manual  
 
The Federal Communications Commission warns that changes or  
modifications of the unit not expressly approved by the party responsible  
for compliance could void the user’s authority to operate the equipment.  
CE mark for Class B ITE (Following European standard EN55022/1998; EN61000-  
3-2/1995; EN61000-3-3/1995, EN55024/1998, EN60950/1992+A1+A2+A3+A4+A11)  
Radio Frequency Interference Statement  
Warning:  
This is a Class B product. In a domestic environment, this product may  
cause radio interference in which case the user may be required to take  
adequate measures.  
Canadian Doc Notice  
For Class B Computing Devices  
This digital apparatus does not exceed the Class B limits for radio noise  
emissions from digital apparatus as set out in the Radio Interference  
Regulation of the Canadian Department of Communications.  
“Le présent appareil numérique n’èmet pas de bruits radioélectriques  
dépassant les limites applicables aux appareils numériques de la class B  
prescrites dans le Règlement sur le brouillage radioélectrique édicté par  
le ministère des Communications du Canada."  
ii  
 
TABLE OF CONTENTS  
TABLE OF CONTENTS ..........................................................................................III  
Your New LCD Monitor  
1
1
3
5
6
6
Unpacking  
Identifying Components  
Adjusting the Tilting Angle  
Connecting AC Power and Video Cable  
Power Management System  
How to install the detacheable stand  
The LCD Monitor's Control Panel  
Adjusting the Monitor’s Display  
TFT LCD Monitor Specifications  
Supported Timing  
7
8
9
15  
17  
18  
Troubleshooting  
iii  
 
The LCD Monitor  
Your New LCD Monitor  
Your LCD Monitor has been designed to be versatile, ergonomic and  
user-friendly. The LCD Monitor is capable of displaying most  
standards, from 640x400 VGA to 1280x1024 SXGA. The digital  
controls located on the front panel allow the user to easily adjust the  
Monitor’s display parameters, and the LCD Monitor’s small footprint  
gives you more room in your workspace for other peripherals.  
Lightweight and compact, the LCD Monitor is the perfect solution for  
users on the go. You can use the LCD Monitor for everything from  
making business presentations to playing computer games. The  
Monitor also has a VESA wall-mount function for added convenience.  
The architecture of the LCD Monitor incorporates an LCD panel  
that produces a clear display with low radiation emission. And with  
its low power consumption, the LCD Monitor helps you reduce your  
power bill.  
Unpacking  
Before unpacking your LCD Monitor, prepare a suitable workspace for  
your LCD Monitor and computer. Look for a stable, level and clean  
surface near a wall outlet. Even though the LCD Monitor uses very  
little power, you should put it in a location which allows sufficient  
airflow to ensure that the LCD Monitor and your computer do not  
overheat. Set up your LCD Monitor so that the panel is not facing a  
window where sunlight often comes in. The glare caused by sunlight  
reflecting off of the LCD Monitor’s screen will make it difficult to use  
the Monitor for viewing.  
Note: Using a computer for an extended period of time with a poor workstation  
set-up and incorrect working habits can cause health problems. The science of  
ergonomics studies the relationship between health and a suitable working  
environment. There is a section on ergonomics at the end of this chapter. For  
more information on ergonomics, contact your nearest computer bookstore, or  
local library. The Internet also has information on this and other subjects.  
1
Rev.1  
 
After unpacking your LCD monitor, make sure the following items are included  
in the box and are in good condition:  
LCD monitor  
Power Cord  
Monitor-To-PC Analog signal cable 15pin  
Monitor-To-PC DVI signal cable  
User’s manual  
If you find that any item to be missing or appear to be damaged,  
contact your dealer immediately. Do not throw away the packing  
material or shipping carton in case you need to ship or store the LCD  
monitor in the future.  
2
Rev.1  
 
Identifying Components  
A. The LCD Monitor — Front View  
3
1
4
2
Figure 1-1: The LCD Monitor Front View  
1. Power-On Indicator  
This Circular LED indicator green lit when the power is on and  
orange lit when the LCD monitor is in power-saving mode.  
2. Monitor Stand  
3. LCD Screen  
The LCD monitor screen is a 19-inch TFT 1280 x 1024 screen.  
4. LCD Monitor Control Panel  
Refer to Chapter 2 for more details.  
3
Rev.1  
 
B. "Hot Keys" for Quick Adjustment of Monitor Settings  
+
P
Figure 1-2: "Hot Keys"  
Brightness  
1. Brightness Adjustment "hot key":  
Press this + button to allow you to  
adjust the brightness of the LCD  
Monitor directly  
50  
Contrast  
2. Contrast Adjustment “ Hot key”  
Press this - button to allow you to  
adjust the contrast of the LCD Monitor  
directly  
50  
3. Auto adjustment “ Hot Key “  
Auto  
Press this  
to allow you to do the  
auto adjustment to get the optimized  
view  
( For VGA port only, DVI port can’t  
adjustment )  
4
Rev.1  
 
Adjusting the Tilting Angle  
The LCD Monitor’s angle settings range from 0° to 10°.  
0 to 10  
Figure 1-3: Tilting the Monitor  
5
Rev.1  
 
Connecting AC Power and Video Cable  
Note: Turn off your PC and the LCD monitor before connecting your  
LCD monitor to the computer.  
AC-IN  
AC Outlet  
(Wall Socket)  
Monitor  
Computer Power Cord  
Power Cord  
DVI  
VGA  
Figure 1-4: The AC Adapter  
Power Management System  
This LCD Monitor complies with the VESA DPMS power  
management proposal.  
When the LCD Monitor is in power-saving mode or detects an  
incorrect timing, the monitor screen will be blank and the power LED  
indicator from green lit change to orange lit.  
6
Rev.1  
 
How to install the detacheable stand:  
Please see the below drawing.  
7
Rev.1  
 
The Display Controls  
The LCD Monitor’s Control Panel  
+
P
Figure 2-1: The Control Panel  
1.  
2.  
: Enable the OSD Menu button or  
/ Move the cursor to the left (when OSD is enabled)  
: Move the cursor to the Right ( When OSD is enabled)  
/ Auto-adjustment hot key  
3. - : Enter into the sub-menu or decrease the value  
/ Contrast hot key  
4. + : Enter into the sub-menu or increase the value  
/ Brightness hot key  
5.  
: Power Switch  
This button lets you turn power for the LCD monitor ON or  
OFF.  
8
Rev.1  
 
Adjusting the Monitor’s Display  
OSD Main Menu  
1. Pressing the Y button causes the screen below to appear.  
2. Use the Y &Z key to select the desired group, then press – or +  
key to enter into sub-menu  
3. Repeat step 2 to select the changed item, then – or + to change  
the value.  
Main Menu  
Sub Menu  
Description  
Monitor Control  
OSD Main SCREEN  
9
Rev.1  
 
Monitor Adjustment  
Allow you to adjust the LCD monitor’s display settings. Press the  
Adjustment control button to display the submenu. Use the Function  
Select button to select one of the following submenu options:  
Auto Adjustment ( For VGA port only, DVI port can’t adjustment )  
Press the Adjustment control button to let the monitor  
determine and select the setting that is most appropriate for  
your system requirements.  
H-POSITION: ( For VGA port only, DVI port can’t adjustment )  
To move the LCD monitor's display left or right on a  
horizontal plane.  
V- POSITION: ( For VGA port only, DVI port can’t adjustment )  
To move the LCD monitor's display up or down on a vertical  
plane.  
PHASE: ( For VGA port only, DVI port can’t adjustment )  
To adjust the focus and clarity of the display  
CLOCK: ( For VGA port only, DVI port can’t adjustment )  
To adjust the display pixel alignment.  
RESET:  
To reset the entire Monitor-Control submenu settings to  
the factory default.  
GRAPHIC/TEXT:  
Press the adjustment control button to switch between  
10  
Rev.1  
 
text and graphic display modes.  
PORT-SELECT:  
To switch between analog and DVI port for PC signal  
input  
EXIT:  
To exits the Monitor-Control submenu  
OSD-control  
The OSD-Control menu lets you adjust the position of the  
OSD on the screen. Press the Adjustment control button to  
display the submenu.  
OSD-H-POSITION:  
To change the position of the OSD on a horizontal plane.  
OSD-V-POSITION:  
To change the position of the OSD on a vertical plane.  
OSD-TIMER:  
The OSD menu display time can be set at 5, 10, 15,  
20, 25 or 30 seconds.  
EXIT:  
To exit the OSD-Control submenu.  
11  
Rev.1  
 
GRAPHIC-CONTROL:  
The Graphic-Control option lets you make adjustments that  
effect the contrast, brightness and color of the LCD monitor’s  
display.  
CONTRAST:  
To adjust the contrast level of the display screen  
BRIGHTNESS:  
To adjust the light level on the display screen.  
COLOR:  
To select the LCD monitor’s color display. The available  
options are cold, warm and User. Selecting the user option  
lets you make individual adjustments to the R, G and B items.  
COLOR R, G and B ADJUST:  
To make individual adjustments to the Red, Blue, Green  
(RGB) gain for the color temperature.  
AUTO LEVEL: To adjust automatically the white balance  
display.  
RESET:  
12  
Rev.1  
 
To reset the entire Graphic-Control submenu settings to  
the factory default.  
EXIT: To exit the Graphic-Control submenu.  
MISC-CONTROL:  
The Misc-Control menu option lets you select the OSD  
display language, adjust the audio volume setting and view  
system information.  
LANGUAGE:  
The supported languages include German, English, French,  
Spanish, Italian and Japanese  
INFORMATION:  
To indicate display mode timings and firmware version.  
EXIT: To exit the Misc-Control submenu.  
EXIT:  
Use the OSD Exit item to close the OSD menu. The OSD will  
disappear by itself if left inactive.  
13  
Rev.1  
 
Note:  
1) No video  
No video  
When the monitor is ON and there is no video signal received, the  
following message will be displayed  
2) Signal out of range  
When the frequency range of the signal is out of the Monitor’s  
specifications, (over 85HZ) the display will show the following  
message  
Over Range  
14  
Rev.1  
 
Appendix A  
TFT LCD Monitor Specifications  
Item  
Specification  
19" SXGA  
LCD Panel  
Control  
Functions  
Power  
Software Power switch with LED indicator  
(ON/OFF)  
On-Screen  
Display  
(OSD)  
Main Menu  
Submenu  
MONITOR-  
CONTROL  
Auto Adjustment, H-POSITION, V-  
POSITION, PHASE, CLOCK,  
GRAPHIC/TEXT, PORT-SELECT,  
RESET, EXIT  
OSD-CONTROL  
OSD-H-POSITION, OSD-V-  
POSITION, OSD-TIMER, EXIT  
MISC-CONTROL LANGUAGE, INFORMATION, EXIT  
GRAPHIC-  
CONTROL  
CONTRAST, BRIGHTNESS, COLOR,  
COLOR R, G and B ADJUST, AUTO  
LEVEL, RESET, EXIT  
EXIT  
Display Area  
(mm)  
376.32 x 301.056  
(19" diagonal)  
Display  
Colors  
16.7 M  
Video  
Interface  
VGA Compatible Analog RGB  
Digital DVI interface  
15  
Rev.1  
 
Item  
Specificaiton  
Scanning Frequency  
H/V, Hz  
24-80K  
50-75  
Power Management  
Meets VESA DPMS  
34W/1W Max.  
Power Consumption  
(ON/OFF, W)  
Dimensions  
WxHxD  
16.54 x 17.4 x 6.89 in.  
(420.2 x 419.04 x 175mm)  
Net Weight  
(approx.)  
11 lbs  
(5 Kg)  
Power Supply  
Environment  
Universal Input AC Socket  
Operating Temperature: 32 to 104°F (0 to 40° C)  
Relative Humidity: 10% to 90%  
Regulatory  
FCC B DoC,UL/cUL,Energy star  
16  
Rev.1  
 
Appendix B  
Supported Timing  
Vertical  
Scanning  
Frequency  
(Hz)  
Horizontal  
Scanning  
Frequency  
(kHz)  
Item  
Standards  
Resolution  
Dot Clock  
(MHz)  
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
NEC PC98  
MAC 13" mode  
MAC 16" mode  
MAC 17" mode  
VGA  
640x400  
640x480  
832x624  
1024x768  
640x350  
640x400  
640x480  
640x480  
640x480  
800x600  
800x600  
800x600  
800x600  
720x400  
1024x768  
1024x768  
1024x768  
1280X1024  
1280X1024  
21.05  
30.24  
57.28  
80.00  
25.18  
25.18  
25.18  
31.50  
31.50  
36.00  
40.00  
50.00  
49.50  
28.32  
65.00  
75.00  
78.75  
108  
56.42  
66.67  
74.55  
75.02  
70.09  
70.09  
59.94  
72.81  
75.00  
56.25  
60.32  
72.19  
75.00  
70.09  
60.00  
70.07  
75.03  
60  
24.83  
35.00  
49.73  
60.24  
31.47  
31.47  
31.47  
37.86  
37.50  
35.16  
37.88  
48.08  
46.88  
31.47  
48.36  
56.48  
60.02  
63.98  
80  
VGA  
VGA  
VESA  
VESA  
VESA  
SVGA  
VESA  
VESA  
VGA  
XGA  
VESA  
VESA  
VESA  
VESA  
135  
75  
*Once a mode is optimized, there is no need to make any further  
adjustment as long as the VGA card remains unchanged.  
*Specifications are subject to change without notice.  
17  
Rev.1  
 
Appendix C  
Troubleshooting  
This LCD monitor comes pre-adjusted with standard VGA timing.  
Due to output timing differences among various VGA cards, you may  
initially experience an unstable or unclear display when a new display  
mode or new VGA card is selected.  
Before applying any of the following troubleshooting procedures, you  
should first apply the Auto Adjust option in the OSD menu.  
PROBLEM: Display is unclear and unstable  
To stabilize and clarify your display, open the OSD and adjust the clock and  
phase to obtain a clear display  
PROBLEM: There is no LCD display  
If there is no display on the LCD, refer to the following:  
1. Make sure that the power indicator on the LCD monitor is lit,  
that all connections are secure, and that the system is running  
on the correct timing. Refer to Appendix B for information on  
timing.  
2. Turn off the LCD monitor and then turn it back on again. Press  
the OSD Menu button (refer to Chapter 2) once and then press  
one of the Adjustment Control buttons several times. If there is  
still no display, press the other Adjustment Control button  
several times.  
3. If step 2 does not work, connect your PC system to another  
external CRT. If your PC system functions properly with a CRT  
monitor but it does not function with the LCD monitor, and the  
LCD monitor’s power LED is blinking, the output timing of the  
PC’s VGA card may be out of the LCD’s synchronous range.  
18  
Rev.1  
 
Change to one of the alternate modes listed in Appendix B, or  
replace the VGA card and repeat steps 1 and 2.  
4. If the power LED is not lit, check that the AC power connector is  
securely connected, and verify that the AC adapter LED is lit. If  
the AC adapter LED is not lit, please contact your dealer for  
assistance.  
PROBLEM: The LCD displays “signal out of range” error message  
1. If you have a CRT monitor, please connect the CRT monitor to  
the computer and change the refresh rate down to 60 Hz via  
your video card’s display settings menu. After the setting of 60  
Hz has been change you can then use the LCD on the  
computer.  
2. If you do NOT have a CRT monitor, please make sure both the  
X9G-NagaV or X9S-NagaV and your computer is turned off.  
Afterwards turn on the LCD and the computer.  
3. While the computer is turned on, press the “F8” key on your  
keyboard continuously until a selection menu appears and  
select the “Safe Mode” option.  
4. When you’ve entered Safe Mode please uninstall any video  
card driver and monitor driver by using either the “Add /  
Remove Programs” icon or going into “System Properties” and  
manually removing anything under “Monitors” and “Display  
Adapters”.  
5. After removing all the drivers, please reboot your computer and  
you should be able to see windows. Please then proceed to  
install your monitor driver first, then your video card driver.  
Please remember to make sure your refresh rate should be at  
60 Hz.  
19  
Rev.1  
 

Q See Security Camera QSDT304C2 User Guide
Q See Security Camera QT528 435 User Guide
Radio Shack Conference Phone ET 469 User Guide
RCA Telephone 25415 User Guide
Regency Indoor Fireplace 944 072 User Guide
Rheem Water Heater Advantage Plus User Guide
RoyalTek GPS Receiver REV 2000 User Guide
Salton Hot Beverage Maker MEK17W User Guide
Samsung DVR 895M User Guide
Schlage Door CYLINDERS User Guide