Shark Carpet Cleaner S3250W User Manual

WWW.SHARKCLEAN.COM  
LIGHT & EASY™ STEAM MOP  
S3250W series  
OWNER’S GUIDE  
 
S3250W_11-S3250W3_11_IB_ENG_100930.indd  
1
10-09-30 10:28 AM  
11. DO NOT unplug by pulling on  
power cord. To unplug, grasp the  
plug not the power cord. Do not  
use extension cords or outlets  
with inadequate current carrying  
capacity.  
21. Extreme caution should be  
exercised when using this  
appliance to clean stairs.  
22. Never use steam mop without  
micro-fiber pad attached.  
23. Keep your work area well lit.  
12. DO NOT put any objects into  
openings. Do not use with any  
opening blocked.  
24. Store steam mop indoors in a cool,  
dry place.  
13. DO NOT put hands or feet under  
25. To avoid circuit overload, do not  
operate another appliance on the  
same socket (circuit) as the steam  
cleaner.  
the steam mop. Unit gets very hot.  
14. Use ONLY on flat, stable horizontal  
surfaces. Do not use on walls,  
counters, windows, chairs or tables.  
26. If an extension cord is absolutely  
necessary, an extension cord rated  
a minimum of 15 ampere, 14 gage  
cord should be used. Cords rated  
for less amperage may overheat.  
Care should be taken to arrange  
cord so that it cannot be pulled or  
tripped over.  
15. DO NOT use on leather, wax  
polished furniture or floors,  
synthetic fabrics, velvet or other  
delicate, steam sensitive materials.  
16. DO NOT add cleaning solutions,  
scented perfumes, oils or any other  
chemicals to the water used in this  
appliance as this may damage the  
unit or make it unsafe for use. If  
you live in a hard water area, we  
recommend using distilled water in  
your steam mop.  
27. DO NOT leave unattended when  
the system is connected to a power  
supply or electrical outlet. Turn off  
all controls before unplugging the  
unit.  
28 DO NOT store unit with damp  
or wet micro-fiber cleaning pad  
attached. Never leave the steam  
mop in one spot on any surface  
for any period of time with a damp  
or wet micro-fiber cleaning pad  
attached as this will damage your  
floors  
17. When in use, NEVER turn the  
appliance over or on its side.  
NEVER DIRECT STEAM TOWARDS  
PEOPLE, ANIMALS OR PLANTS.  
18. Carefully remove the micro-  
fiber pad immediately after you  
have unplugged and allowed the  
product to cool.  
WARNING: Your steam mop  
is designed to clean hard floor  
surfaces that will withstand high  
heat. Do not use on unsealed wood  
or unglazed ceramic floors. On  
surfaces that have been treated  
with wax or some no wax floors,  
the sheen may be removed by  
the heat and steam action. It is  
always recommended to test an  
isolated area of the surface to be  
cleaned before proceeding. We also  
recommend that you check the use  
and care instructions from the floor  
manufacturer.  
19. When cleaning the steam mop,  
unplug the power cord from the  
electrical outlet and clean with a  
dry or damp cloth. Do not pour  
water or use alcohol, benzene or  
paint thinner on the unit.  
20 To reduce the risk of fire, DO NOT  
use a flammable or combustible  
liquid to clean a floor.  
 
S3250W_11-S3250W3_11_IB_ENG_100930.indd  
3
10-09-30 10:28 AM  
Quick Start  
fig. 3  
fig. 1  
fig. 2  
ASSEMBLE  
FILL  
1
Fit the extension tubes together  
as shown in the illustration.  
(fig. 1)  
3
Remove the cap to fill the  
water tank. Use the filling flask  
and funnel to fill the tank with  
water to the “MAX” fill line.  
Replace the water tank cap.  
(fig. 3)  
2
Place the micro-fiber cleaning  
pad underneath the mop head,  
with quick fastener strips facing  
up. Simply press the mop to the  
pad to attach it. (fig. 2)  
TOLL FREE: 1-800-798-7398  
 
S3250W_11-S3250W3_11_IB_ENG_100930.indd  
4
10-09-30 10:28 AM  
fig. 5  
fig. 4  
STEAM CLEANING  
4 Plug in the mop. Wait 30  
BACKSAVER  
5
Use the Shark® Light &  
Easy™ with backsaver  
benefit to access tight  
areas. Press the release  
button on the handle  
to lock the Light &  
seconds for the unit to heat up  
and the steam to be ready.  
Push the handle toward the  
mop head in a pumping motion.  
Customize steam output by slow  
or fast mopping with a forward  
and backward motion. (fig. 4)  
Easy™ Steam Mop in the  
backsaver position. Press  
the release button on the  
handle again to straighten  
the handle. (fig. 5)  
 
S3250W_11-S3250W3_11_IB_ENG_100930.indd  
5
10-09-30 10:28 AM  
This manual covers model numbers:  
S3250W 11  
S3250W3 11  
TECHNICAL SPECIFICATIONS  
Voltage: 120V., 60Hz.  
Power: 1550 Watts  
Water  
Capacity: 250 ml (8 oz.)  
TOLL FREE: 1-800-798-7398  
 
S3250W_11-S3250W3_11_IB_ENG_100930.indd  
6
10-09-30 10:28 AM  
Contents  
GETTING STARTED.................................................................2  
USING YOUR STEAM MOP...................................................6  
STORAGE AND CARE OF YOUR STEAM MOP ........... 9  
TROUBLESHOOTING .............................................................11  
WARRANTY AND REGISTRATION...................................13  
Thank you for  
purchasing  
the Shark®  
Light & Easy  
Steam Mop.  
 
S3250W_11-S3250W3_11_IB_ENG_100930.indd  
1
10-09-30 10:28 AM  
Getting Started  
When assembling your steam mop there  
may be a little water in or around the  
water tank. This is because we test all  
our steam mops 100% before you  
buy them, so you get a quality  
Shark® Light & EasySteam Mop.  
b
c
b
a
d
f
a
e
fig. 1  
a Upper Handle Tube with Backsaver  
ASSEMBLY  
benefit  
1
Remove all the parts from the  
package. Verify all the listed parts  
are included.  
b Lower Tube  
c Steam Mop Base  
d 2 All-Purpose Cleaning Pads  
e Filling Flask  
2 Insert the long gray end of the lower  
pole (a) into the Backsaver handle  
(b). Press gently until you hear them  
click into place. (fig. 1)  
f Funnel  
2
TOLL FREE: 1-800-798-7398  
 
S3250W_11-S3250W3_11_IB_ENG_100930.indd  
2
10-09-30 10:28 AM  
English  
c
fig. 2  
3 Take the assembled pole and insert  
it into the base of the mop (c). Align  
the notches and press gently until  
you hear it click into place. (fig. 2)  
IMPORTANT: Never use the Light &  
Easy™ Steam Mop without attaching a  
micro-fiber cleaning pad to avoid  
damage to your floor and mop.  
3
 
S3250W_11-S3250W3_11_IB_ENG_100930.indd  
3
10-09-30 10:28 AM  
Getting Started  
Your micro-fiber cleaning  
pads should be replaced  
every 3 months to maximize  
cleaning performance.  
fig. 1  
ATTACHING THE MICRO-FIBER PAD  
Replacement micro-fiber pads are  
available at www.sharkclean.com or  
by calling 1-800-798-7398.  
1
Place the micro-fiber cleaning pad  
on the floor with the quick fastener  
strips facing up. Place the Light &  
Easy™ Steam Mop on the top of the  
pad to attach. (fig. 1)  
IMPORTANT: Only add water to  
the tank. Chemicals or cleaning  
solutions may be unsafe or cause  
damage.  
4
TOLL FREE: 1-800-798-7398  
 
S3250W_11-S3250W3_11_IB_ENG_100930.indd  
4
10-09-30 10:28 AM  
English  
fig. 2  
fig. 3  
FILLING THE WATER TANK  
2 A filling flask and funnel are included  
with your Light & Easy™ Steam Mop  
to make filling the water tank easy.  
Fill the flask with water and use the  
funnel to pour it into the tank. Keep  
the water level under the “MAX” fill  
line. (fig. 3)  
IMPORTANT: Unplug the Light &  
Easy™ Steam Mop before filling the  
water tank with water. (fig. 2)  
1
Remove the water tank cap by  
turning it counter-clockwise to the  
unlocked position. (fig. 3)  
3 Replace the water tank cap and turn  
it clockwise to the locked position.  
5
 
S3250W_11-S3250W3_11_IB_ENG_100930.indd  
5
10-09-30 10:28 AM  
Using Your Light & Easy™ Steam Mop  
When you use your steam mop for the  
first time or if you have not used the unit  
in awhile, it may take a minute or two  
for the water to travel through the pump  
and into the heater to create steam. Get  
it started by pumping the handle a few  
times. If you have waited a few minutes  
and you still do not see any steam,  
reference the troubleshooting section  
on page 11.  
fig. 1  
fig. 2  
fig. 3  
IMPORTANT: Your steam mop needs  
water to make steam! Never use  
your steam mop without water in the  
tank.  
1
Pull and twist the quick release  
cord holder to unwrap the power  
cord completely. (fig. 1) Plug into  
a 120-volt electrical outlet. (fig. 2)  
The “On” light will turn blue. If the  
light does not turn on, reference the  
troubleshooting section on page 11.  
(fig. 3)  
Sweep or vacuum your floors prior  
to cleaning with your Light & Easy™  
Steam Mop.  
Visit www.sharkclean.com for other  
great quick cleaning products to  
complement your Light & Easy™  
Steam Mop, such as the Shark®  
SV800 Cordless Stick Vac.  
6
TOLL FREE: 1-800-798-7398  
 
S3250W_11-S3250W3_11_IB_ENG_100930.indd  
6
10-09-30 10:28 AM  
English  
If your Light & Easy Steam  
Mop stops steaming, it could  
be out of water. Unplug the  
power cord from the electrical  
outlet and refill the water tank  
at anytime.  
fig. 4  
fig. 5  
2 Wait 30 seconds for the boiler to  
heat the water. Pump the handle  
a few times to prime the pump,  
activate steam and moisten the  
micro-fiber pad. (fig. 4)  
3 Mop with a forward and backward  
motion to customize steam output  
automatically. (fig. 5)  
7
 
S3250W_11-S3250W3_11_IB_ENG_100930.indd  
7
10-09-30 10:28 AM  
Using Your Light & Easy™ Steam Mop  
fig. 1  
1
Clean under furniture and tight  
areas using the Shark® Backsaver™  
locking handle. Press the handle  
release button and apply slight  
pressure to bend the handle. The  
Shark® Backsaver™ joint will lock at  
a perfect, access-maximizing angle.  
(fig. 1)  
2 Press the release button on the  
handle again to straighten.  
8
TOLL FREE: 1-800-798-7398  
 
S3250W_11-S3250W3_11_IB_ENG_100930.indd  
8
10-09-30 10:28 AM  
English  
Care of Your Light & Easy™ Steam Mop  
fig. 1  
fig.3  
fig.2  
AFTER USE AND STORAGE  
4 To store the cooled Shark® Light &  
1
When you have finished using the  
Light & Easy™ Steam Mop, unplug  
the cord from the outlet and place  
the mop into the upright position  
(fig. 1) and let the unit cool 2-3  
minutes. Release steam by pumping  
the handle several times.  
Easy™ Steam Mop, hang on a large  
hook. (fig. 3)  
NOTE: If you want to store the  
Light & Easy™ Steam Mop standing  
upright, make sure it is leaning  
against a wall for added support and  
safety. Always store your Shark®  
Light & Easy™ Steam Mop with the  
micro-fiber cleaning pad removed.  
Store away from children and high  
traffic areas.  
2 Carefully separate micro-fiber  
cleaning pad from steam mop,  
avoiding contact with the hot pocket  
or dirt. (fig. 2)  
3 Empty the water tank before storage.  
Remove the water tank cap and  
empty the tank over a sink. Replace  
the water cap.  
9
 
S3250W_11-S3250W3_11_IB_ENG_100930.indd  
9
10-09-30 10:28 AM  
Care of Your Light & Easy™ Steam Mop  
fig. 5  
fig. 6  
CARE OF YOUR MICRO-FIBER  
CLEANING PAD  
ORDERING REPLACEMENT PARTS  
To order additional parts and  
accessories, feel free to contact us at  
1-800-798-7398.  
1
Wash pads in warm water. Wash  
separately from other laundry. Only  
use liquid detergent (no powder  
detergent). Do not use fabric  
softeners. Line dry or dry on a low  
dryer setting. (fig. 5)  
NOTE: Some parts may be available  
at your local retailer. Contact customer  
service for any other servicing.  
2 If there are loose threads on the  
pad carefully cut the threads with  
scissors. Do not pull on them or cut  
at the base. (fig. 6)  
IMPORTANT: The micro-fiber  
cleaning pad may be very hot  
from the steam. Use caution when  
removing. Let the unit cool for 2-3  
minutes.  
10  
TOLL FREE: 1-800-798-7398  
 
S3250W_11-S3250W3_11_IB_ENG_100930.indd 10  
10-09-30 10:28 AM  
English  
Trouble Shooting  
PROBLEM  
POSSIBLE REASONS & SOLUTIONS  
Your steam-mop should be securely plugged into a  
120V AC electrical outlet only.  
The Light & Easy™  
Steam Mop will not  
turn-on.  
Check your fuse or breaker.  
If your unit still does not work, call 1-800-798-7398.  
Light & Easy™  
Steam Mop will not  
make steam.  
Is there water in the water tank? If not, add water to your  
Steam Mop following instructions on page 5.  
Light & Easy™  
Steam Mop leaves  
water on the floor.  
Is your micro-fiber cleaning pad too wet? Unplug your  
Steam Mop and change the micro-fiber cleaning pad.  
Do not leave your steam-mop on the floor with a damp or  
wet cleaning pad.  
Light & Easy™  
Steam Mop left  
white spot on the  
floor.  
Do you have hard water? If you do, you might want to  
switch to distilled water.  
Make sure the water is securely on the water tank.  
The pad might be dirty, change the pad.  
If you washed the pocket with powder detergent, then the  
pad may have residual detergent left on it. Wash it again  
with liquid detergent.  
If you are cleaning in a kitchen area where there might be a  
build-up of grease, use a de-greasing agent such as an all-  
purpose cleaner or dish soap and paper towels to clean the  
area first.  
Floors are cloudy,  
streaky or spotty  
after steaming.  
You might have left the mop in the same spot for too long.  
Do you have hard water? If you do, you might want to  
switch to distilled water.  
This might be leftover from past cleaners used on the floor  
surface. Use the steam mop a few more times and see if  
the leftover cloudiness is removed.  
Make sure the steam pad is attached correctly.  
Light & Easy™  
Steam Mop is hard  
to push.  
Check to see if the cleaning pad is excessively dirty.  
Replace if the pad is too dirty or wet.  
11  
 
S3250W_11-S3250W3_11_IB_ENG_100930.indd 11  
10-09-30 10:28 AM  
Notes  
12  
TOLL FREE: 1-800-798-7398  
 
S3250W_11-S3250W3_11_IB_ENG_100930.indd 12  
10-09-30 10:28 AM  
English  
ONE (1) YEAR LIMITED WARRANTY  
EURO-PRO Operating LLC warrants this product to be free from defects in material and  
workmanship for a period of one (1) year from the date of the original purchase, when utilized for  
normal household use, subject to the following conditions, exclusions and exceptions.  
If your appliance fails to operate properly while in use under normal household conditions  
within the warranty period, return the complete appliance and accessories, freight prepaid. For  
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC  
will repair or replace it free of charge. Proof of purchase date and a check made out to EURO-  
PRO Operating LLC in the amount of $ 9.95 to cover the cost of return shipping and handling  
must be included.*  
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or  
replacement of the unit at our option. This warranty does not cover normal wear of parts and  
does not apply to any unit that has been tampered with or used for commercial purposes. This  
limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage  
due to faulty packaging or mishandling in transit. This warranty does not cover damage or  
defects caused by or resulting from damages from shipping or repairs, service or alterations to  
the product or any of its parts, which have been performed by a repair person not authorized by  
EURO-PRO Operating LLC.  
This warranty is extended to the original purchaser of the unit and excludes all other legal and/  
or conventional warranties. The responsibility of EURO-PRO Operating LLC warranty if any,  
is limited to the specific obligations expressly assumed by it under the terms of the limited  
warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential  
damages of any nature whatsoever. Some states/provinces do not permit the exclusion or  
limitation of incidental or consequential damages, so the above may not apply to you.  
This warranty gives you specific legal rights, and you may also have other rights which vary from  
state to state or province to province.  
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of  
purchase date and to attach tag to item before packing with your name, complete address and  
phone number with a note giving purchase information, model number and what you believe  
is the problem with the item. We recommend you insure the package (as damage in shipping  
is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER  
SERVICE”. We are constantly striving to improve our products, therefore the specifications  
contained herein are subject to change without notice.  
OWNERSHIP REGISTRATION CARD FOR  
CANADIAN CONSUMERS ONLY  
Please complete and return within ten (10) days of purchase. The registration will enable  
us to contact you in the event a product defect is discovered. By returning this card you  
acknowledge to have read and understood the instructions for use, and warnings set  
forth in the accompanying instructions.  
RETURN TO: EURO-PRO Operating LLC, 4400 Bois Franc, St. Laurent, Quebec H4S 1A7  
PURCHASER: ……………………………………………………………………………………………............  
ADDRESS: ………………………………………………………………………………………………...............  
S3250W 11 / S3250W3 11  
DATE OF PURCHASE: …………………….. MODEL: ………………...................................  
NAME AND ADDRESS OF STORE: …………………………………………………………………..  
13  
 
S3250W_11-S3250W3_11_IB_ENG_100930.indd 13  
10-09-30 10:28 AM  
Euro-Pro Operating LLC  
US: Newton, MA 02459  
CAN: Ville St-Laurent, QC H4S 1A7  
English: 1-800-798-7398  
COPYRIGHT© EURO-PRO OPERATING LLC 2010  
PRINTED IN CHINA  
Illustrations may differ from actual product.  
S3250W/W3.E.100930  
 
S3250W_11-S3250W3_11_IB_ENG_100930.indd 14  
10-09-30 10:28 AM  

Sharp All in One Printer MX M182 User Manual
Shure Wireless Office Headset BRH440M User Manual
Sierra Wireless Cell Phone 20070914 User Manual
Sony Battery Charger AC VQ800 User Manual
Sony Camcorder 3 286 590 121 User Manual
Sony Carrying Case MPK WB User Manual
Sony MP3 Player DSX S300BTX User Manual
Sony Speaker SS M9ED User Manual
Stiga Lawn Mower 43 COMBI User Manual
Sungale Clock CA700VCR User Manual