CADET™ OVAL
COUNTERTOP SINK
VITREOUS CHINA
BARRIER FREE
CADET™ OVAL COUNTERTOP SINK
• European-styled interior bowl
• Available with Scotchgard® finish for
easier cleaning
• Made from vitreous china
• Self-rimming with cutout template supplied
• Front overflow
❏ 0419.444 Faucet holes on 4" (102mm) centers
❏ 0419.888 Faucet holes on 8" (203mm) centers
(illustrated)
❏ 0419.111 Center hole only
❏ 0419.444SG Faucet holes on 4" (102mm) centers
(with Scotchgard® finish)
❏ 0419.888SG Faucet holes on 8" (203mm) centers
Available with
(with Scotchgard® finish)
Nominal Dimensions:
21" x 17-5/8"
(533 x 448mm)
FINISHED WALL
OR SPLASHBACK
8"
24
(610mm)
OPTIONAL
(203mm)
2-3/4"
(70mm)
4
(102mm)
Bowl sizes:
16-1/2" (419mm) wide
7-7/8"
(200mm)
11" (279mm) front to back
5-5/8" (143mm) deep
17-5/8"
(488mm)
1-3/4" DIA.
STD. DRAIN
OUTLET
8
DRAWING FOR
DIMENSIONAL
PURPOSES ONLY.
IT IS NOT AN EXACT
REPRESENTATION.
(203mm)
MIN.
Compliance Certifications -
Meets or Exceeds the
Following Specifications:
845mm
(33-1/4)
27
(686mm)
MIN.
SEALING
COMPOUND
21"
(533mm)
6
3/4"
(19mm)
COUNTERTOP
(BY OTHERS)
(152mm)
MAX.
• ASME A112.19.2M for
Vitreous China Fixtures
• CAN/CSA B45 series
BARRIER FREE
CLEARANCE
7-1/2"
(190mm)
9
(229mm)
MIN.
*10-3/4"
(273mm)
*12-7/8"
(327mm)
31"
(787mm)
SUGGESTED
SUPPLIES
AS REQ'D
To Be Specified:
❏ Color: ❏ White ❏ Bone
8"
(203mm)
33-1/4"
(845mm)
1-1/4" O.D. WASTE
❏ Linen ❏ Silver
1-1/4" O.D. TAILPIECE
❏ Fawn Beige ❏ Black
FINISHED FLOOR
❏ Faucet*:
❏ Faucet Finish:
❏ Supplies:
❏ 1-1/4" Trap:
NOTES:
* See faucet section for additional models available
DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE
*
SUGGESTED.
FOR COUNTERTOP CUTOUT AND INSTALLATION INSTRUCTIONS USE
TEMPLATE SUPPLIED WITH SINK.
FITTINGS NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED
SEPARATELY.
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES
AND ANSI A117.1 ACCESSIBLE AND USABLE
SEALING COMPOUND SUPPLIED BY OTHERS.
BUILDINGS AND FACILITIES - CHECK LOCAL CODES.
Install lavatory 864mm (34") from finished floor.
Lavatory installed 51mm (2") minimum from front edge
of countertop provides 686mm (27") knee clearance area.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range
of tolerances established by ANSI Standard A112.19.2. These measurements
are subject to change or cancellation. No responsibility is assumed for use of
superseded or voided pages.
J41
© 2008 AS America Inc.
Revised 2/08
|
3Com Network Router 3C840 User Manual
3Com Two Way Radio B 406 User Manual
3M Marine Instruments 48N User Manual
Abit Computer Hardware AT7 User Manual
Abocom Network Router WAP404 User Manual
ACCO Brands Electric Heater H65 User Manual
Acer Computer Monitor G226HQLBbd User Manual
AOC Marine Instruments E1659FWU User Manual
Atlona Printer Accessories AT HDMI V42 User Manual
Axis Communications Digital Camera 223M User Manual