Clarion Cassette Player ARX7570Z User Manual

Owner’s manual

Mode d’emploi

Manual de instrucciones

ARX7570z

AM/FMCASSETTEPLAYER

WITHCD/MDCHANGERCONTROL

•

LECTEURDECASSETTEAM/FMAVEC

COMMANDEDECHANGEURCD/MD

•

RADIODEAM/FMYREPRODUCTORDE

CASETESCONCONTROLDECAMBIADORDE

DISCOSCOMAPCTOS/MINIDISCOS

OPEN

ARX7570z

ISR

Clarion Co., Ltd.

PE-1639B

280-7232-00

Printed in China / Imprimé en Chine / Inpreso en China

1999/1 (A·C)

Handling Cassette Tapes

6. REMOTE CONTROL

1. FEATURES

Using any of the following types of cassette

tapes can cause malfunctions.

• Avoid using cassettes of 120 minutes or

longer. (Such cassettes have extremely thin

tape, so the tape can become stretched or

cut.)

• Periodically play a cleaning cassette in the

player to clean the head.

• Keep magnet items like magnets, and iron and

steel items like screwdrivers away from both

cassette tapes and the tape head in the player.

• Do not oil the cassette mechanism.

• Do not use any cassette tapes with peeling

labels or deformed cases. Such cassette tapes

can cause breakdowns.

• When not using the player, always take the

cassette out of the mechanism. Exposing a

cassette to direct sunlight, extreme tempera-

tures or high humidity can damage the cas-

sette.

Receiver for remote control unit

■ Rotary Encoder Volume Control with Illuminated Search Key

■ Touch-n-Go Flip Down Detachable Face

• Cassette tapes with low recording levels

• Cassette tapes in which the unrecorded sec-

tion between tracks is shorter than 4 seconds

• Cassette tapes with noise or the like recorded

between tracks

OPEN

■ Controller for Optional TV Tuner Module

■ Capability to Read CD TEXT Data from Clarion Compatible CD Changer

■ Z-Enhancer with 3 Adjustment Modes

ARX7570z

■ CeNET with Balanced Audio Line Transmission and Dynamic Noise Canceling

ISR

■

^®FM Reception System

• Cassette tapes on which there are long unre-

corded sections in the middle of a track

■ Full Logic Tape Transport with True Function / Auto Reverse with Dual Azimuth Adjust

■ Dolby ^®B Noise Reduction

Operating range: 30° in all directions

Handling precautions

■ 4-Channel RCA Line Level Output with Fader Control

■ 2-Channel Non-Fade RCA Line Level Output

■ 160W (40W×4) Maximum Power Output

• Slack in the tape can cause malfunctions. In

particular for prerecorded cassette tapes and

90-minute tapes, take up any slack in the tape

before inserting it into the cassette player.

Signal transmitter

Remote control unit

2. PRECAUTIONS

This unit uses a precision mechanism. Even in the event that trouble arises, never open the case,

disassemble the unit, or lubricate the rotating parts.

This equipment generates, uses, and can radi-

ate radio frequency energy and, if not installed

Flip Down Panel

CAUTION

and used in accordance with the instructions,

may cause harmful interference to radio com-

munications. However, there is no guarantee

that interference will not occur in a particular

installation.

CHANGES OR MODIFICATIONS NOT EX-

PRESSLY APPROVED BY THE MANUFAC-

TURER FOR COMPLIANCE COULD VOID

THE USER’S AUTHORITYTO OPERATETHE

EQUIPMENT.

The ARX7570z uses a flip-down structure that makes possible large-size displays.

3. Do not use the FLIP DOWN PANEL as a tray

CAUTION

to place objects on when it is open.

When opening and closing the FLIP DOWN

PANEL, be careful not to catch your fingers.

They could be injured.

4. When closing the FLIP DOWN PANEL, do not

If this equipment does cause harmful interfer-

ence to radio or television reception, which can

be determined by turning the equipment off and

on, the user is encouraged to consult the dealer

or an experienced radio/TV technician for help.

INFORMATION FOR USERS:.

press the OPEN button 1.

CHANGES OR MODIFICATIONS TO THIS

PRODUCT NOT APPROVED BY THE MANU-

FACTURER WILL VOID THE WARRANTY

AND WILL VIOLATE FCC APPROVAL.

5. Strong impacts to the operating or display

section can cause damage or deformation.

1. Always use the ARX7570z with the FLIP

DOWN PANEL closed.

6. If the FLIP DOWN PANEL does not open fully,

gently open it with your hand.

Inserting the Batteries

2. Do not force operations or use this device

abnormally when opening or closing the FLIP

DOWN PANEL.

1. Turn the remote control unit over, then slide

the rear cover in the direction of the arrow.

AA (UM-3/1.5V)

Batteries

2. Insert the AA (UM-3/1.5V) batteries that

came with the remote control unit facing in

the directions shown in the figure, then close

the rear cover.

Notes:

Using batteries improperly can cause them to ex-

plode. Take note of the following points:

•When replacing batteries, replace both batteries

with new ones.

Rear cover

Rear side

•Do not short-circuit, disassemble or heat batteries.

•Do not dispose of batteries into fire or water.

•Dispose of spent batteries properly.

Be sure to unfold and read the next page.

Veuillez déplier et vous référer à la page suivante.

Cerciórese de desplegar y de leer la página siguiente.

ARX7 5 7 0 z

3. CONTROLS / LES COMMANDES / CONTROLES

4. NOMENCLATURE

5. DCP

Note:

The control panel can be detached to prevent theft. When detaching the control panel, store it in the

DCP (DETACHABLE CONTROL PANEL) case to prevent scratches.

• Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page 5 (unfold).

Source unit / Appareil pilote / Unidad fuente

We recommend taking the DCP with you when leaving the car.

Names of Buttons

Removing the DCP

1. Hold down POWER button 3 for 1 second or

Attaching the DCP

1. Insert the right side of the DCP into the source

unit.

1 OPEN button

8 Z-EHCR (z-enhancer) button

9 Preset buttons (1 to 6)

Direct buttons (1 to 6) (7 to 12)

0 DISP (display) button

! ISR (instant station recall) button

@ BND (band) button

2 ENT (enter) button

Play/pause button

longer to turn off the power.

OPEN

ARX7570z

2. Insert the left side of the DCP into the source

unit.

3 POWER button

FNC (function) button

4 TITLE button

ISR

ADJ (adjust) button

PROG (program) button

# A-M (audio mode) button

LOUD (loudness) button

$ SEARCH button

5 PS/AS (preset scan/auto store) button

SCN (scan) button

2. Deeply push in OPEN button 1 to unlock the

FLIP DOWN PANEL.

6 RPT (repeat) button

BLS (blank skip) button

7 DOLBY NR button

RDM (random) button

With the FLIP DOWN PANEL opened / Ouverture du PANNEAU RABATTABLE /

Apertura del PANEL ABATIBLE

If the FLIP DOWN PANEL does not open fully,

gently open it with your hand.

% Rotary knob

¥ Cassette tape insertion slot

& Eject button

CAUTION

• The DCP can easily be damaged by shocks.

After removing it, be careful not to drop it

or subject it to strong shocks.

Display Items

• If the FLIP DOWN PANEL is kept open, the

DCP may drop due to vibration of the car.

Cassette tape in indication

CD/MD changer mode indication

Long title indication

This results in damage to the DCP. So close

the FLIP DOWN PANEL or remove the DCP

to store into the case.

BLS (blank skip) indication

3. Pull the DCP toward you and remove it.

When the texts for CD or MD are more than

11 characters, this indication lights.

Z-EHCR (z-enhancer) indication

Preset channel indication (1 to 6)

Disc number indication (1 to 12)

DCP

• The connector connecting the source unit

and the DCP is an extremely important part.

Be careful not to damage it by pressing on

it with fingernails, screwdrivers, etc.

Operation status indication

The frequency, play time, clock, etc. are dis-

played.

The disc numbers corresponding to the discs

in the CD or MD changer light.

Display / Afficheur / Visualizador

Note:

RDM (random) indication

RPT (repeat) indication

SCN (scan) indication

DISC indication

MANU (manual) indication

ST (stereo) indication

• If the DCP is dirty, wipe off the dirt with a soft, dry

cloth only.

Function mode indication

The names of modes being selected, etc. are

displayed.

4. Close the HOLD FLAP.

Dolby B NR indication

LD (loudness) indication

A-M (audio mode) indication

HOLD FLAP

Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter.

Remarque: Veuillez déplier cette page et vous référer aux schémas quand vous lisez chaque chapitre.

Nota: Cuando lea los capítulos, despliegue esta página y consulte los diagramas.

CAUTION

Be sure to close the HOLD FLAP for safety

when removing the DCP.

ARX7 5 7 0 z

Functions of Remote Control Unit Buttons

CD changer

MD changer

Mode

Radio

Tape

Button

) FUNC

Turns power on and off. When pressed and held for 1 second: Turns power off.

Switches among radio, tape, CD changer, MD changer and TV.

¡ BAND

Switches the side of Moves the next disc

Switches reception

band.

Switches reception

band.

DISC UP

the tape.

in increasing order.

PROG

TOP

Increases and decreases volume (in all modes).

™ VOLUME

£ SEARCH

Moves preset

channels up and

down.

Fast-forward and

rewinds tape.

APC fast-forward

and rewind.

Moves tracks up

and down.

When pressed and down.

held for 1 second:

Fast-forward/

Moves preset

channels up and

fast-backward.

¢ PLAY/PAUSE

No function.

Switches between

No function.

playback and pause. playback and pause.

Turns mute on and off.

∞

MUTE

Recalls ISR radio station in memory.

§ ISR

Press and hold for 2 seconds or longer: Stores current station into ISR memory (radio

mode only).

Switches among main display, sub display and clock display .

¶ DISP

• SCN

Fast-forward scan.

Preset scan.

Scan play.

When pressed and When pressed and

held for 2 seconds: held for 2 seconds:

Preset scan.

PS/AS

When pressed and

held for 2 seconds:

Auto store.

Disc scan play.

Auto store.

ª RPT

No function.

Repeat play.

No function.

BLS

When pressed and

held for 1 second:

Blank tape skip

function turns on

and off.

When pressed and

held for 2 seconds:

Disc repeat play.

º RDM

Select Dolby Noise

Reduction mode.

No function.

Random play.

When pressed and TV and VTR.

held for 2 seconds:

Switches between

DOLBY NR

MONI

Disc random play.

* Some of the corresponding buttons on the source unit and remote control unit have different functions.

^{ARX7 5 7 0 z}

7. OPERATIONS

Note: Be sure to read this chapter referring to the front diagrams of

chapter “3. CONTROLS” on page 5 (unfold).

Basic Operations

Radio mode ➜ Tape mode ➜ CD changer

mode ➜ MD changer mode ➜ TV mode ➜

CAUTION

Radio mode...

Be sure to lower the volume before switch-

ing off the unit power or the ignition key.The

unit remembers its last volume setting. If you

switch the power off with the volume up, when

you switch the power back on, the sudden

loud volume may hurt your hearing and dam-

age the unit.

External equipment not connected with CeNET

is not displayed.

Adjusting the volume

Turning the Rotary knob % clockwise increases

the volume; turning it counterclockwise de-

creases the volume.

The clock is displayed when the ignition key

is turned to the ACC (accessory) or IGN (igni-

tion-on) position even when the unit power

is off. In some cars, the clock may momen-

tarily disappear when the ignition key is

turned to the START position. The clock will

reappear after the engine has started and the

ignition key is released to the IGN (ignition-

on) position.

The volume level is from 0 (minimum) to 33 (maxi-

mum).

Switching the display

Press DISP button 0 to select the desired display.

Each time you press DISP button 0, the display

switches in the following order:

Main display

Turning on/off the power

Note:

• Be careful about using this unit for a long time with-

out running the engine. If you drain the car’s bat-

tery too far, you may not be able to start the en-

gine and this can reduce the service life of the

battery.

Sub (title) display

1. Press POWER button 3.

2. The illumination and display on the unit light

up. The unit automatically remembers its last

operation mode and will automatically switch

to display that mode.

3. Press and hold POWER button 3 for 1 sec-

Clock display

ond or longer to turn off the power for the unit.

Note:

• System check

The first time this unit is turned on after the wire

connections are completed, it must be checked

what equipment is connected. When the power is

turned on, “SYSTEM CHCK” appears in the dis-

play, so press POWER button 3. The system

check starts within the unit. When the system

check is complete, the power is turned off, so press

POWER button 3 again.

Main display...

Once selected, the preferred display becomes

the display default. When a function adjustment

such as volume is made, the screen will mo-

mentarily switch to that function’s display, then

revert back to the preferred display several

seconds after the adjustment.

When you have entered a title in a CD, it ap-

pears in the sub display. If you have not en-

tered a title, “NO-TTL” appears in the title dis-

play instead. For information on how to enter a

title, refer to the subsection “Entering titles”

in the “Other Handy Functions”.

Selecting a mode

1. Press FNC button 3 to change the mode of

operation.

2. Each time you press FNC button 3, the mode

of operation changes in the following order:

^{ARX7 5 7 0 z}

Basic Operations

Adjusting the bass

Setting the Z-enhancer

This unit comes with 3 types of sound tone effects

stored in memory. Select the one you prefer.

1. Press A-M button # and select “BASS”.

2. Turning the Rotary knob % clockwise empha-

sizes the bass; turning it counterclockwise

attenuates the bass.

The factory default setting is “Z-EHCR OFF”.

Each time you press Z-EHCR button 8, the tone

effect changes in the following order:

The factory default setting is “0”. (Adjustment

range: –6 to +6)

The bass cannot be adjusted if the tone by-

pass setting is “YES” (ON).

“Z-ENHANCER 1” ➜ “Z-ENHANCER 2” ➜ “Z-

ENHANCER 3” ➜ “Z-EHCR OFF” ➜ “Z-EN-

HANCER 1”...

3. When the adjustment is complete, press A-M

button # several times until the function mode

is reached.

• Z-ENHANCER 1 : bass emphasized

• Z-ENHANCER 2 : treble emphasized

• Z-ENHANCER 3: bass and treble emphasized

• Z-EHCR OFF

: no sound effect

Adjusting the treble

1. Press A-M button # and select “TREBLE”.

Adjusting the tone

2. Turning the Rotary knob % clockwise empha-

sizes the treble; turning it counterclockwise

attenuates the treble.

Press A-M button # and select the item to ad-

just. Each time you press A-M button #, the item

changes in the following order:

The factory default setting is “0”. (Adjustment

range: –6 to +6)

●

When the Z-enhancer and tone bypass are off

The treble cannot be adjusted if the tone by-

pass setting is “YES” (ON).

“T-BYPASS” ➜ “BASS” ➜ “TREBLE” ➜

“BALANCE” ➜ “FADER” ➜ Function mode...

3. When the adjustment is complete, press A-M

button # several times until the function mode

is reached.

● When Z-enhancer 1, 2 or 3 is set

“Z-EHCR” ➜ “BALANCE” ➜ “FADER” ➜

Function mode...

Adjusting the balance

1. Press A-M button # and select “BALANCE”.

Setting tone bypass

The tone bypass disables the tone (bass and

treble) functions and cuts the noise generated

when the tone functions are on.

2. Turning the Rotary knob % clockwise empha-

sizes the sound from the right speaker; turn-

ing it counterclockwise emphasizes the sound

from the left speaker.

1. Press A-M button # and select “T-BYPASS”.

2. Turning the Rotary knob % clockwise sets the

tone bypass to “YES” (ON); turning it coun-

terclockwise sets the tone bypass to “NO”

(OFF).

The factory default setting is “0”. (Adjustment

range: L13 to R13)

3. When the adjustment is complete, press A-M

button # several times until the function mode

is reached.

The factory default setting is “NO” (OFF).

If the setting is “YES” (ON), the bass and treble

adjustments cannot be made.

Adjusting the fader

1. Press A-M button # and select “FADER”.

3. When the adjustment is complete, press A-M

button # several times until the function mode

is reached.

2. Turning the Rotary knob % clockwise empha-

sizes the sound from the front speakers; turn-

ing it counterclockwise emphasizes the sound

from the rear speakers.

Note:

• If you set the Z-ENHANCER function to ON (1 to

3), you cannot set the tone bypass.

The factory default setting is “0”. (Adjustment

range: F12 to R12)

3. When the adjustment is complete, press A-M

button # several times until the function mode

is reached.

^{ARX7 5 7 0 z}

Basic Operations

Radio Operations

Adjusting the Z-enhancer

1. Press Z-EHCR button 8 and select the Z-

FM reception

For enhanced FM performance the

enhancer mode (1 to 3) to adjust.

tuner includes signal actuated stereo control, En-

hanced Multi AGC, Impulse noise reduction circuits

and Multipath noise reduction circuits.

2. Press A-M button # and select “Z-EHCR”.

3. Turning the Rotary knob % clockwise adjusts

in the + direction; turning it counterclockwise

adjusts in the – direction.

Changing the reception area

This unit is initially set to USA frequency intervals

of 10 kHz for AM and 200 kHz for FM.When using

it outside the USA, the frequency reception range

can be switched to the intervals below.

When Z-enhancer 1 is selected, you can adjust

the bass in the range of ±2.

When Z-enhancer 2 is selected, you can adjust

the treble in the range of ±2.

When Z-enhancer 3 is selected, you can adjust

the bass and treble in the range of ±2.

● Setting the reception area

1. Press BND button @ and select the desired

4. When the adjustment is complete, press A-M

button # several times until the function mode

is reached.

radio band (FM or AM).

2. While pressing RDM button 7, each time you

press and hold the number “1” of the Preset

buttons 9 for 2 seconds or longer, the re-

ception area switches from inside the USA to

outside the USA or from outside the USA to

inside the USA.

Note:

• If you set the Z-ENHANCER function to ON (1 to

3), you cannot set the tone bypass.

Turning on/off the loudness

Any station preset memories are lost when the

reception area is changed.

The loudness effect emphasizes the bass and

treble to create a natural sound tone. When you

are listening to music at a low volume, it is rec-

ommended to use the loudness effect.

Listening to the radio

1. Press FNC button 3 and select the radio

1. Press and hold LOUD button # for 1 second

or longer to turn on the loudness effect.When

the loudness effect is turned on, “LD” lights in

the display.

mode.

2. Press BND button @ and select the radio

band. Each time the button is pressed, the

radio reception band changes in the follow-

ing order:

2. Press and hold LOUD button # for 1 second

or longer to turn off the loudness effect. “LD”

goes off in the display.

FM1 ➜ FM2 ➜ FM3 ➜ AM ➜ FM1...

3. Press the right or left side of SEARCH button

$ to tune in the desired station.

Tuning

There are 3 types of tuning mode available, seek

tuning, manual tuning and preset tuning.

Seek tuning

1. Press BND button @ and select the desired

band (FM or AM).

If “MANU” is lit in the display, press and hold

BND button @ for 1 second or longer. “MANU”

in the display goes off and seek tuning is now

available.

2. Press the right or left side of SEARCH button

$ to automatically seek a station.

When the right side of SEARCH button $ is

pressed, the station is sought in the direction

of higher frequencies; if the left side of

SEARCH button $ is pressed, the station is

sought in the direction of lower frequencies.

^{ARX7 5 7 0 z}

Radio Operations

Manual tuning

Auto store

There are 2 ways available: Quick tuning and step

tuning.

When you are in the step tuning mode, the fre-

quency changes one step at a time. In quick tun-

ing mode, you can quickly tune the desired fre-

quency.

Auto store is a function for storing up to 6 sta-

tions that are automatically tuned in sequentially.

If 6 stations cannot be received, a previously

stored station remains unoverwritten at the

memory position.

1. Press BND button @ and select the desired

band (FM or AM).

2. Press and hold AS button 5 for 2 seconds or

longer. The stations with good reception are

stored automatically to the Preset buttons 9.

If “MANU” is not lit in the display, press and

hold BND button @ for 1 second or longer.

“MANU” lights in the display and manual tun-

ing is now available.

Preset scan

2. Tune into a station.

Preset scan receives the stations stored in pre-

set memory in order.This function is useful when

searching for a desired station in memory.

● Quick tuning:

Press and hold the right or left side of

SEARCH button $ for 1 second or longer to

tune in a station.

1. Press PS button 5.

2. When a desired station is tuned in, press PS

button 5 again to continue receiving that sta-

tion.

● Step tuning:

Press the right or left side of SEARCH button

$ to manually tune in a station.

Note:

• Be careful not to press and hold PS button 5 for

2 seconds or longer, otherwise the auto store func-

tion engages and the unit starts storing stations.

Recalling a preset station

A total of 24 preset positions (6-FM1, 6-FM2, 6-

FM3, 6-AM) exists to store individual radio sta-

tions in memory.Pressing the corresponding pre-

set button recalls the stored radio frequency au-

tomatically.

Instant station recall (ISR)

Instant station recall is a special radio preset that

instantly accesses a favorite radio station at a

touch of a button. The ISR function even oper-

ates with the unit in other modes.

1. Press BND button @ and select the desired

band (FM or AM).

2. Press the corresponding Preset button 9 to

● ISR memory

1. Select the station that you wish to store in ISR

recall the stored station.

Press and hold one of the Preset buttons 9

for 2 seconds or longer to store that station

into preset memory.

memory.

2. Press and hold ISR button ! for 2 seconds

or longer.

● Recalling a station with ISR

In any mode, press ISR button ! to turn on the

radio function and tune the selected radio sta-

tion. “ISR” appears in the display. Press ISR but-

ton ! again to return to the previous mode.

Manual memory

1. Select the desired station with seek tuning,

manual tuning or preset tuning.

2. Press and hold one of the Preset buttons 9

for 2 seconds or longer to store the current

station into preset memory.

^{ARX7 5 7 0 z}

Tape Operations

Loading a tape

Ejecting a tape

1. Press OPEN button 1 to access the cassette

tape insertion slot behind the FLIP DOWN

PANEL.

1. Press OPEN button 1 to access the cassette

Eject button & behind the FLIP DOWN

PANEL.

2. Load a tape into the cassette tape insertion

slot. “LOADING” appears in the display and

starts playing.

2. Press Eject button & to eject a tape and take

it out.

3. Close the FLIP DOWN PANEL.

When a metal or chrome bias (70µ sec) tape is

inserted, the metal tape setting is selected auto-

matically.

CAUTION

3. Close the FLIP DOWN PANEL.

Be careful not to catch your hand or fingers

while closing the FLIP DOWN PANEL.

Notes:

CAUTION

• If the FILP DOWN PANEL does not open fully, gen-

tly open with your hand.

• The radio mode is selected automatically 4 sec-

Be careful not to catch your hand or fingers

while closing the FLIP DOWN PANEL.

Notes:

onds after Eject button & is pressed.

• If the FILP DOWN PANEL does not open fully, gen-

tly open with your hand.

If the auto antenna terminal for this unit is con-

nected, the antenna is extended automatically. If

you are in a location where the antenna may strike

something, press FNC button 3 to switch the

mode.

• Do not leave the FLIP DOWN PANEL open. Be

sure to close it to avoid any possible mechanical

damage.

• Do not put your hands, fingers or foreign objects

into the cassette tape insertion slot.

• When a tape has already been loaded in the cas-

sette tape insertion slot, another one cannot be

inserted into it. Never try to insert another tape

forcibly.

Switching to the other side of the tape

Press PROG button @ to change tape direction

and playback.

The tape mechanism automatically reverses di-

rection and engage playback at the end of the tape

(auto reverse).

Listening to a tape already inserted

Press FNC button 3 to select the tape mode.

The tape starts playing automatically. If no tape

is loaded in the unit, “NO CASSETTE” appears

in the display.

Fast-forwarding/rewinding

● FF(fast-forward):

Press the right side of SEARCH button $.

● REW(rewind):

Press the left side of SEARCH button $.

● Canceling FF/REW:

Press Play/pause button 2.

Pausing tape play

1. Press Play/pause button 2 to pause tape

playback. “PAUSE” appears in the display.

When the end of the tape is reached with FF/REW,

the mechanism automatically reverses tape direc-

tion and resumes playback.

2. Press Play/pause button 2 again to resume

tape playback.

If you select another mode during FF/REW, it is

selected with FF/REW continued.

The mechanism automatically makes FF/REW

stop when the end of the tape is reached.

This function is called “monitor mode”.

^{ARX7 5 7 0 z}

Tape Operations

2. To cancel the intro tape scan, press SCN but-

ton 5 again. “SCN” goes off from the display

and the current track continues to play.

APC (Auto Program Control) function

The APC function allows the tape to skip forward

to the beginning of the next track or rewind to

the start of the current track.

When the end of the tape is reached during the

intro tape scan, the tape mechanism automatically

reverses direction and continues the intro tape

scan.

● Skipping forward to the next track (“APC-

FF”)

During tape playback, press the right side of

SEARCH button $ twice to fast-forward to the

next track. The next track starts playing.

If you select another mode during the intro tape

scan, the mechanism automatically makes the intro

tape scan stop when it finds the next track (APC

function).

● Skipping backwards to the start of the cur-

rent track (“APC-REW”)

During tape playback, press the left side of

SEARCH button $ twice to rewind to the start

of the current track. The current track plays from

the beginning.

Tape selection repeat

The tape selection repeat continuously plays the

current track.This function continues automatically

until it is canceled.

1. Press RPT button 6. “RPT” lights in the dis-

play and the current track is repeated.

2. To cancel the repeat play, press RPT button

6 again.“RPT” goes off from the display and

normal play resumes.

● Canceling FF/REW APC to resume playback

Press Play/pause button 2.

If you select another mode during APC mode, it is

selected with APC mode continued.

The mechanism automatically makes APC mode

stop when it finds the next track (in APC-FF) or

the start of the current track (in APC-REW). This

function is called “monitor mode”.

Blank tape skip

The blank tape skip allows you to skip blank sec-

tions of tape that are over 12 seconds long.

1. Press and hold RPT button 6 for 1 second

or longer. “BLS” lights in the display and the

mechanism fastforward to the next track se-

lection.

2. To cancel the blank tape skip, press and hold

RPT button 6 for 1 second or longer again.

“BLS” goes off from the display and normal

play resumes.

Dolby noise reduction system

The Dolby noise reduction system increases the

volume level of high frequency sounds during

recording and sets it back to their original level

during play. This system reduces hissing noise

which is typical of cassette tapes.

Dolby noise reduction manufactured under license

from Dolby Laboratories Licensing Corporation.

Dolby and the double-D symbol are trademarks of

Dolby Laboratories Licensing Corporation.

1. Press DOLBY NR button 7 to select Dolby

noise reduction. Each time you press DOLBY

NR button 7, the Dolby type changes in the

following order:

Notes:

The APC, intro tape scan, tape selection repeat and

blank skip may not work properly with tapes of the

following qualities:

• Tapes on which the recording level is too low.

• Tapes on which there is much noise between se-

lections.

• Tapes on which there are long pauses in the middle

of selections.

• Tapes on which there are less than 4 seconds of

blank space between selections.

DOLBY B NR ON➜DOLBY NR OFF➜DOLBY

B NR ON....

2. When DOLBY B NR ON is selected, “DOLBY

B NR” appears in the display.

Intro tape scan

The intro tape scan allows the first 10 seconds

of all the tracks on the tape to be played.

This function continues automatically until it is

canceled.

1. Press SCN button 5 to start the intro tape

scan. “SCN” lights in the display.

^{ARX7 5 7 0 z}

Other Handy Functions

Setting the clock

Entering titles

1. Press and hold ADJ button 4 for 1 second or

longer to switch to the adjustment selection

display.

Titles up to 10 characters long can be stored in

memory and displayed for radio stations and

CDs. The numbers of titles that can be entered

for each mode are as follows.

2. Press the right or left side of SEARCH button

$ to select “CLOCK”.

Mode

Number of titles

30 titles

3. Press ENT button 2.

Radio mode

TV mode

4. Press the right or left side of SEARCH button

15 titles

$ to select the hour or the minute.

CD changer mode

CDC655z connected

CDC655Tz connected

CDC1255z connected

Number of titles

60 titles

5. Turn the Rotary knob % clockwise or coun-

terclockwise to set the correct time.

100 titles

The clock is displayed in 12-hour format.

6. Press ENT button 2 to store the time into

memory.

50 titles

1. Press FNC button 3to select the mode you want

7. Press ADJ button 4 to return to the previous

to enter a title (radio, CD changer or TV).

mode.

Titles cannot be entered for MDs with this unit.

2. Select and play a CD in a CD changer or tune

to an appropriate TV or radio station.

Note:

• You cannot set the clock when it is displayed with

only the ignition on. If you drain or remove the car’s

battery or take out this unit, the clock is reset.

While setting the clock, if another button or opera-

tion is selected, the clock set mode is canceled.

3. Press DISP button 0 and display the sub-

title.

4. Press TITLE button 4. “TITL” appears in the

display and the cursor position flashes.

Dimmer level setting

You can reduce the display illumination linked to

the car illumination.

5. Press the right or left side of SEARCH button

$ to move the cursor.

6. Press DISP button 0 to select a character.

Each time you press DISP button 0, the char-

acter changes in the following order:

The factory default setting is “LEVEL 3”.

1. Press and hold ADJ button 4 for 1 second or

longer to switch to the adjustment selection

display.

Capital letters ➜ Small letters ➜ Numbers ➜

Symbols ➜ Capital letters...

2. Press the right or left side of SEARCH button

7. Turn the Rotary knob % to select the desired

character. Turning the Rotary knob % clock-

wise moves the cursor to the next character;

turning it counterclockwise moves the cursor

to the previous character.

$ to select “DIMMER LV”.

3. Press ENT button 2.

4. Turn the Rotary knob % clockwise or coun-

terclockwise to set the dimmer level. Choose

the dimmer level from the following.

8. Repeat steps 5 to 7 to enter up to 10 charac-

ters for the title.

“OFF”, “LEVEL 1”, “LEVEL 2”, “LEVEL 3”,

“LEVEL 4”, “LEVEL 5”.

9. Press and hold ENT button 2 for 2 seconds

or longer to store the title into memory and

cancel title input mode.

LEVEL 1 to LEVEL 5:

The greater the dimmer level is, the more the

illumination is reduced.

Clearing titles

OFF:

1. Play a CD in a CD changer or tune a radio

station or TV station that you want to clear

the title for.

Even if the car illumination is turned on, re-

duction of the display illumination does not

occur.

2. Press DISP button 0 and display the sub-

5. Pressing ENT button 2 returns to the adjust-

title.

ment selection display.

3. Press TITLE button 4. “TITL” appears in the

display and the display switches to the title

input display.

6. Press ADJ button 4 to return to the previous mode.

^{ARX7 5 7 0 z}

Other Handy Functions

4. Press BND button @.

Triggered audio mute for cellular

telephones

This unit requires special wiring to mute the au-

dio signal automatically when a cellular telephone

rings in the car.

5. Press and hold ENT button 2 for 2 seconds

or longer to clear the title and cancel the title

input mode.

Adjusting the display contrast

You can adjust the display contrast according to

the angle of installation of the unit.

This function is not compatible with all cellular tele-

phones. Contact your local authorized Clarion

dealer for information on proper installation and

compatibility.

The factory default setting is “6”. (Adjustment level:

1 to 11)

1. Press and hold ADJ button 4 for 1 second or

longer to switch to the adjustment selection

display.

2. Press the right or left side of SEARCH button

$ to select “CONTRAST”.

3. Press ENT button 2.

4. Turn the Rotary knob % clockwise or coun-

terclockwise to adjust the contrast.

5. Pressing ENT button 2 returns to the adjust-

ment selection display.

6. Press ADJ button 4 to return to the previous

mode.

Message display

When the unit is powered on or off, a message is

displayed. The user can turn this message dis-

play on or off.

The factory default setting is “ON”.

1. Press and hold ADJ button 4 for 1 second or

longer to switch to the adjustment selection

display.

2. Press the right or left side of SEARCH button

$ to select “MESSAGE”.

3. Press ENT button 2.

4. Turn the Rotary knob % clockwise to set the

message display to “ON”; turn it counterclock-

wise to set the message display to “OFF”.

5. Pressing ENT button 2 returns to the adjust-

ment selection display.

6. Press ADJ button 4 to return to the previous

mode.

^{ARX7 5 7 0 z}

8. OPERATIONS OF ACCESSORIES

CD Changer Operations

CD changer functions

Selecting a CD

When an optional CD changer is connected

through the CeNET cable, this unit controls all

the CD changer functions. This unit can control

a total of 2 changers (MD and/or CD).

Each of the Direct button 9 corresponds to a

disc loaded into the magazine.

● Selecting a disc from 1 to 6

Press the corresponding Direct button 9 (1 to

Press FNC button 3 and select the CD changer

mode to start play. If 2 CD changers are con-

nected, press FNC button 3 to select the CD

changer for play.

6) to select the desired disc.

● Selecting a disc from 7 to 12 (only when a

12 disc CD changer is used.)

Press and hold the corresponding Direct button

9 (7 to 12) for 1 second or longer to select the

desired disc.

If “NO MAGAZINE” appears in the display, insert

the magazine into the CD changer.“DISC CHECK”

appears in the display while the player loads

(checks) the magazine.

If “NO DISC” appears in the display, eject the

magazine and insert discs into each slot. Then,

reinsert the magazine back into the CD changer.

If a CD is not loaded in a slot of the magazine,

pressing the Direct button 9 corresponding to its

disc number is invalid.

Selecting a track

● Track-up

CAUTION

1. Press the right side of SEARCH button $ to

CD ROM discs cannot be played in the CD

changer.

move ahead to the beginning of the next track.

2. Each time you press the right side of SEARCH

button $, the track advances ahead to the

beginning of the next track.

Pausing play

1. Press Play/pause button 2 to pause play.

“PAUSE” appears in the display.

● Track-down

1. Press the left side of SEARCH button $ to

move back to the beginning of the current

track.

2. To resume play, press Play/pause button 2

again.

2. Press the left side of SEARCH button $ twice

Displaying CD titles

This unit can display title data for CD-text CDs

and user titles input with this unit.

to move to the beginning of the previous track.

Fast-forward/fast-backward

1. Press DISP button 0 to display the title.

● Fast-forward

2. Each time you press and hold DISP button

0 for 1 second or longer, the title display

changes in the following order:

Press and hold the right side of SEARCH button

$ for 1 second or longer.

● Fast-backward

User title (disc) ➜ CD-text title (disc) ➜ CD-

text title (track) ➜ user title (disc)...

Press and hold the left side of SEARCH button

Note:

$ for 1 second or longer.

• If the CD playing is not a CD-text CD or no user

title has been input, “NO-TTL” appears in the dis-

play.

● Scrolling a CD-text title

When a CD-text title is longer than 11 charac-

ters, you can scroll the display as follows.

1. Display the CD-text title (disc or track).

2. Press TITLE button 4. The title scrolls.

^{ARX7 5 7 0 z}

CD Changer Operations

Disc repeat play

Top function

The top function plays from the first track (track

No. 1) of the disc.

After all the tracks on the current disc have been

played, the disc repeat play automatically replays

the current disc over from the first track.This func-

tion continues automatically until it is canceled.

● When playing a disc 1 to 6

Press the Direct button 9 (1 to 6) with the same

number as the CD playing.

1. Press and hold RPT button 6 for 1 second

or longer. “DISC” and “RPT” light in the dis-

play and the disc repeat play starts.

● When playing a disc 7 to 12 (only when a

12 disc CD changer is used).

2. To cancel the disc repeat play, press and hold

RPT button 6 again. “DISC” and “RPT” go

off from the display and normal play resumes

on the current track.

Press and hold for 1 second or longer the Direct

button 9 (7 to 12) with the same number as the

CD playing.

If a CD is not loaded in a slot of the magazine,

pressing the Direct button 9 corresponding to its

disc number is invalid.

Random play

The random play selects and plays individual

tracks on the disc in no particular order.This func-

tion continues automatically until it is canceled.

Scan play

The scan play locates and plays the first 10 sec-

onds of each track on a disc automatically. This

function continues on the disc until it is canceled.

1. Press RDM button 7. “RDM” lights in the dis-

play and the random play begins.

The scan play is useful when you want to select a

desired track.

2. To cancel the random play, press RDM but-

ton 7 again. “RDM” goes off from the dis-

play and normal play resumes.

1. Press SCN button 5 to start track scanning.

“SCN” lights in the display.

2. To cancel the scan play, press SCN button 5

again. “SCN” goes off from the display and

the current track continues to play.

Disc random play

The disc random play selects and plays individual

tracks or discs automatically in no particular or-

der. This function continues automatically until it

is canceled.

Disc scan play

The disc scan play locates and plays the first 10

seconds of the first track on each disc in the cur-

rently selected CD changer. This function con-

tinues automatically until it is canceled.

1. Press and hold RDM button 7 for 1 second

or longer. “DISC” and “RDM” light in the

display and the disc random play starts.

2. To cancel the disc random play, press and

hold RDM button 7 again. “DISC” and “RDM”

go off from the display and normal play re-

sumes from the current track.

The disc scan play is useful when you want to

select a desired CD.

1. Press and hold SCN button 5 for 1 second

or longer. “DISC” and “SCN” light in the dis-

play and the disc scan play starts.

2. To cancel the disc scan play, press SCN but-

ton 5 again. “DISC” and “SCN” go off from

the display and the current track continues to

play.

Repeat play

The repeat play continuously plays the current

track. This function continues automatically until

it is canceled.

1. Press RPT button 6. “RPT” lights in the dis-

play and the current track is repeated.

2. To cancel the repeat play, press RPT button

6 again. “RPT” goes off from the display and

normal play resumes.

^{ARX7 5 7 0 z}

MD Changer Operations

2. Each time you press the right side of SEARCH

button $, the track advances ahead to the

beginning of the next track.

MD changer functions

When an optional MD changer is connected

through the CeNET cable, this unit controls all

the MD changer functions. This unit can control

a total of 2 changers (MD and/or CD).

● Track-down

1. Press the left side of SEARCH button $ to

move back to the beginning of the current track.

Press FNC button 3 and select the MD changer

mode to start play. If 2 MD changers are con-

nected, press FNC button 3 to select the MD

changer for play.

2. Press the left side of SEARCH button $ twice

to move to the beginning of the previous track.

If “NO DISC” appears in the display, load MDs

into the MD changer.

Fast-forward/fast-backward

● Fast-forward

Press and hold the right side of SEARCH button

$ for 1 second or longer.

Pausing play

1. Press Play/pause button 2 to pause play.

“PAUSE” appears in the display.

● Fast-backward

Press and hold the left side of SEARCH button

$ for 1 second or longer.

2. To resume play, press Play/pause button 2

again.

Top function

Switching disc titles and track titles

The top function plays from the first track (track

No. 1) of the disc. Press the Direct button 9 (1

to 6) with the same number as the MD playing.

This unit can display disc titles and track titles

already entered on MDs. Titles up to 128 char-

acters long can be displayed by scrolling the

titles.

If an MD is not loaded in a slot of the MD changer,

pressing the Direct button 9 corresponding to its

disc number is invalid.

Titles cannot be entered for MDs with this unit.

1. Press DISP button 0 to display the title. The

disc title or track title is displayed.

Scan play

The scan play locates and plays the first 10 sec-

onds of each track on a disc automatically. This

function continues on the disc until it is canceled.

2. Each time you press and hold DISP button

0 for 1 second or longer, the display toggles

between the disc title and the track title.

The scan play is useful when you want to select a

desired track.

●Scrolling titles

When a title is longer than 11 characters, you

can scroll through it with the following operation.

1. Press SCN button 5 to start track scanning.

“SCN” lights in the display.

1. Display the MD title (disc or track).

2. Press TITLE button 4.

2. To cancel the scan play, press SCN button 5

again. “SCN” goes off from the display and

the current track continues to play.

The display scrolls through the title.

Selecting an MD

Disc scan play

Each of the Direct button 9 corresponds to an

MD loaded into the MD changer. Press the cor-

responding Direct button 9 (1 to 6) to select the

desired disc.

The disc scan play locates and plays the first 10

seconds of the first track on each disc in the cur-

rently selected MD changer. This function con-

tinues automatically until it is canceled.

If an MD is not loaded in a slot of the MD changer,

pressing the Direct button 9 corresponding to its

disc number is invalid.

The disc scan play is useful when you want to

select a desired MD.

1. Press and hold SCN button 5 for 1 second

or longer.“DISC”and “SCN” light in the display

and the disc scan play starts.

Selecting a track

● Track-up

2. To cancel the disc scan play, press and hold

SCN button 5 again. “DISC” and “SCN” go

off from the display and the current track con-

tinues to play.

1. Press the right side of SEARCH button $ to

move ahead to the beginning of the next track.

^{ARX7 5 7 0 z}

MD Changer Operations

Repeat play

TV Operations

TV tuner functions

The repeat play continuously plays the current

track. This function continues automatically until

it is canceled.

When an optional TV tuner is connected through

the CeNET cable, this unit controls all TV tuner

functions. To watch TV requires a TV tuner and

monitor.

1. Press RPT button 6. “RPT” lights in the dis-

play and the current track is repeated.

Watching a TV

1. Press FNC button 3 and select theTV mode.

2. To cancel the repeat play, press RPT button

6 again. “RPT” goes off from the display and

normal play resumes.

2. Press BND button @ to select the desired TV

band (TV1 or TV2). Each time the button is

pressed, the input selection toggles between

TV1 and TV2.

Disc repeat play

After all the tracks on the current disc have been

played, the disc repeat play automatically replays

the current disc over from the first track.This func-

tion continues automatically until it is canceled.

3. Press the right or left side of SEARCH button

$ to tune in the desired TV station.

1. Press and hold RPT button 6 for 1 second

or longer. “DISC” and “RPT” light in the dis-

play and the disc repeat play starts.

Watching a video

The TV tuner has a VTR input terminal to which

1 external device can be connected. Connect a

12V video cassette player (VCP) or video cas-

sette recorder (VCR) to the TV tuner input termi-

nal.

2. To cancel the disc repeat play, press and hold

RPT button 6 again. “DISC” and “RPT” go

off from the display and normal play resumes

on the current track.

1. Press RDM button 7 to select VTR.

2. To return to the TV broadcast, press RDM

Random play

button 7.

The random play selects and plays individual

tracks on the disc in no particular order.This func-

tion continues automatically until it is canceled.

Tuning

There are 3 types of tuning mode available, Seek

tuning, manual tuning and preset tuning.

1. Press RDM button 7. “RDM” lights in the dis-

play and the random play begins.

2. To cancel the random play, press RDM but-

ton 7 again. “RDM” goes off from the dis-

play and normal play resumes.

Seek tuning

1. Press BND button @ to select the desired TV

band (TV1 or TV2).

If “MANU” is lit in the display, press and hold

BND button @ for 1 second or longer. “MANU”

in the display goes off and seek tuning is now

available.

Disc random play

The disc random play selects and plays individual

tracks or discs automatically in no particular or-

der. This function continues automatically until it

is canceled.

2. Press the right or left side of SEARCH button

$ to automatically seek a station.

Press the right side of SEARCH button $ to

automatically tune up the frequency band to

the next available TV station; press the left

side to automatically tune down.

1. Press and hold RDM button 7 for 1 second

or longer. “DISC” and “RDM” light in the dis-

play and the disc random play starts.

2. To cancel the disc random play, press and

hold RDM button 7 again. “DISC” and “RDM”

go off from the display and normal play re-

sumes from the current track.

^{ARX7 5 7 0 z}

TV Operations

Manual tuning

There are 2 ways available: Quick tuning and step

tuning.

When you are in the step tuning mode, the fre-

quency changes one step at a time. In quick tun-

ing mode, you can quickly tune the desired fre-

quency.

1. Press BND button @ and select the desired

TV band (TV1 or TV2).

2. Press and hold AS button 5 for 2 seconds or

longer. The stations with good reception are

automatically stored to the Preset buttons 9.

Preset scan

1. Press BND button @ and select the desired

Preset scan allows the user to view each preset

position before it automatically advances to the

next preset. This function is useful for searching

for desired TV station in memory.

band (TV1 or TV2).

If “MANU” is not lit in the display, press and

hold BND button @ for 1 second or longer.

“MANU” lights in the display and manual tun-

ing is now available.

1. Press PS button 5.

2. When the desired station is found, press PS

2. Tune into a station.

button 5 again to remain tuned to that station.

● Quick tuning:

Note:

Press and hold the right or left side of

SEARCH button $ for 1 second or longer to

tune in a station.

• Do not press and hold PS button 5 for 2 seconds

or longer. Doing so will trigger the auto store func-

tion and start storing stations into memory.

● Step tuning:

Setting the TV diver

Press the right or left side of SEARCH button

$ to manually tune in a station.

You can change the reception setting for the TV

antenna connected to the TV tuner.

Recalling a preset station

1. Press and hold ADJ button 4 for 1 second or

longer to switch to the adjustment selection

display.

A total of 12 TV stations can be stored (6-TV1

and 6-TV2). This allows you to select your favor-

iteTV stations and store them in memory for later

recall.

2. Press the right or left side of SEARCH button

$ to select “TV DIVER”.

1. Press BND button @ and select the desired

3. Press ENT button 2.

TV band (TV1 or TV2).

4. Turn the Rotary knob % clockwise to set to

“ON” or counterclockwise to set to “OFF”.

2. To recall a stored TV station, press the de-

sired Preset button 9 to select that station.

ON:

Press and hold one of the Preset buttons 9

for 2 seconds or longer to store the current sta-

tion into the preset memory.

Sets reception emphasizing the visual.

OFF:

Sets the diver setting to OFF.

5. Press ENT button 2.

Manual memory

1. Select the desired station with seek tuning,

manual tuning or preset tuning.

6. Press ADJ button 4 to return to the previous

mode.

2. Press and hold one of the Preset buttons 9

for 2 seconds or longer to store the current

station to that preset memory.

Auto store

Auto store selects 6 TV stations automatically

and stores each one into a preset memory.

If there are not 6 stations with good reception,

stations previously stored in memory remain and

only the strong stations are stored into memory.

^{ARX7 5 7 0 z}

9. TROUBLESHOOTING

Problem

Cause

Measure

Power does not

turn on.

Fuse is blown.

Replace with a fuse of the same amperage. If the

fuse blows again, consult your store of purchase.

(No sound is

produced.)

Incorrect wiring.

Consult your store of purchase.

No sound output Power antenna lead is

1. Turn the unit off.

when operating

the unit with

amplifiers or

power antenna

attached.

shorted to ground or

2. Remove all wires attached to the power antenna

lead. Check each wire for a possible short to

ground using an ohm meter.

excessive current is required

for remote-on the amplifiers

or power antenna.

3. Turn the unit back on.

4. Reconnect each amplifier remote wire to the

power antenna lead one by one. If the amplifiers

turn off before all wires are attached, use an

external relay to provide remote-on voltage

(excessive current required).

Nothing happens The microprocessor has

when buttons are malfunctioned due to noise,

Turn off the power, then press OPEN button 1 and

remove the DCP.

Press the reset button for about 2 seconds with a thin

pressed.

etc.

rod.

Reset button

Display is not

accurate.

DCP or source unit

connectors are dirty.

Wipe the dirt off with a soft cloth moistened with

cleaning alcohol.

Sound quality is

poor.

Playback head is dirty.

Use a cleaning tape, etc., to clean the head.

DOLBY NR button 7 is not

pressed.

When listening to a tape recorded with Dolby NR,

press DOLBY NR button 7 and select B NR.

^{ARX7 5 7 0 z}

10. ERROR DISPLAYS

If an error occurs, one of the following displays is displayed.

Take the measures described below to eliminate the problem.

Cause

Error Display

ERROR 1

Measure

Tape cannot be played due to defective

tape such as cut tape.

Eject the tape then replace it with a new

one.

ERROR 2

ERROR 4

Tape is caught and cannot be played.

Tape mode cannot be detected.

Remove the caught or wound tape.

This is a failure of tape mechanism and

consult your store of purchase.

ERROR 8

ERROR 2

ERROR 3

ERROR 6

ERROR H

Tape is caught and cannot be ejected.

Eliminate the reason for which the tape is

caught.

A CD inside the CD changer is not loaded. This is a failure of CD changer’s mecha-

nism and consult your store of purchase.

A CD inside the CD changer cannot be

played due to scratches, etc.

Replace with a non-scratched, non-warped

disc.

A CD inside the CD changer cannot be

played because it is loaded upside-down.

Eject the disc then reload it properly.

Displayed when the temperature in the

MD changer is too high and playback has

been stopped automatically.

Lower the surrounding temperature and

wait for a while to cool off MD changer.

ERROR 2

ERROR 3

ERROR 6

An MD inside the MD changer is not

loaded.

This is a failure of MD changer’s mecha-

nism and consult your store of purchase.

An MD inside the MD changer cannot be

played due to scratches, etc.

Replace with a non-scratched, non-warped

disc.

An MD inside the MD changer cannot be

played because it is loaded upside-down.

Eject the disc then reload it properly.

Displayed when a non-recorded MD is

loaded in the MD changer.

Load a pre-recorded MD in the MD

changer.

If an error display other than the ones described above appears, press the reset button. If the problem

persists, turn off the power and consult your store of purchase.

^{ARX7 5 7 0 z}

11. SPECIFICATIONS

FM Tuner

Frequency Range:

87.9 MHz to 107.9 MHz

Audio

Maximum Power Output:

160 W (40 W × 4 ch) (EIAJ)

Usable Sensitivity:

11 dBf

Continuous Average Power Output:

14 W × 4, into 4 Ω, 20 Hz to 20 kHz, 1%THD

50dB Quieting Sensitivity:

17 dBf

Bass Control Action (30 Hz):

±15 dB

Alternate Channel Selectivity:

75 dB

Treble Control Action (10 kHz):

±10 dB

Stereo Separation (1 kHz):

35 dB

Line Output Level (0VU tape):

0.7 V

Frequency Response (±3 dB):

30 Hz to 15 kHz

General

Power Supply Voltage:

14.4 V DC (10.8 to 15.6 V allowable),

negative ground

AM Tuner

Frequency Range:

530 kHz to 1710 kHz

Current Consumption:

Less than 15 A

Usable Sensitivity:

25 µV

Speaker Impedance:

4 Ω (4 Ω to 8 Ω allowable)

Tape Deck

Wow & Flutter (WRMS):

Weight / Source unit:

3.52 lb. (1.6 kg)

0.06%

Weight / Remote control unit:

1 oz. (30 g) (including battery)

Channel Separation (1 kHz):

45 dB

Dimensions / Source unit:

7" (Width) × 2" (Height) × 6-1/8" (Depth)

[178 (W) × 50 (H) × 155 (D) mm]

Frequency Response (±3 dB):

120 µs (normal):

Dimensions / Remote control unit:

1-3/4" (Width) × 4-5/16" (Height) × 1-1/8" (Depth)

[44 (W) × 110 (H) × 27 (D) mm]

30 Hz to 18 kHz

70 µs (CrO2, FeCr, Metal):

30 Hz to 20 kHz

Signal to Noise Ratio, 70 µs (CrO2, FeCr, Metal)

Dolby NR OFF:

58 dB

Dolby B NR:

67 dB

Notes:

• Specifications comply with EIA Standards.

• Specifications and design are subject to change without notice for further improvement.

^{ARX7 5 7 0 z}

Memo

^{ARX7 5 7 0 z}

Cooper Lighting Marine Safety Devices HR87C User Manual
Craftsman Trimmer 3587958 User Manual
Crosley Clothes Dryer W10223589B User Manual
Curtis Telephone T223 User Manual
DMP Electronics Smoke Alarm XR2500F User Manual
Ducane Gas Grill 27010332 User Manual
Dynex Digital Camera DX WC100 User Manual
Edimax Technology Network Card HP 8501 User Manual
Fortinet Network Card 5001A DW User Manual
GE Air Conditioner AEM10 User Manual