Flymo Blower 2700XV User Manual

TWISTER

2700XV

Original Instructions

For all customer enquiries or for replacement parts, contact:-

¤ 01325 300303

www.flymo.com

customer.services@husqvarna.co.uk

3. Do not use the product if the electric cables are dam-

aged or worn.

condition before use.

Use

4. Immediately disconnect from the mains electricity supply if

the cable is cut, or the insulation is damaged. Do not touch

the electric cable until the electrical supply has been dis-

connected. Do not repair a cut or damaged cable. Re-

place it with a new one.

1. Use the product only in daylight or good artificial light.

2. Do not use the product when it is raining or in damp

and wet areas.

3. Never use the product in or near water or ponds.

4. Know how to stop the product quickly in an emergency.

5. On slopes, be extra careful of your footing and wear

non-slip footwear.

5. Your electric cable must be uncoiled, coiled cables can

overheat and reduce the efficiency of the product.

6. Do not pull cable around sharp objects.

7. Always switch off at the mains before disconnecting any

plug, cable connector or extension cable.

6. Do not walk backwards whilst operating your prod-

uct, you could trip. Walk, never run.

7. Always direct the cable to the rear, away from the product.

8. Keep children, pets and bystanders at a safe dis-

tance when using your product.

8. Switch off, remove plug from mains and examine

electric supply cable for damage or ageing before

winding cable for storage. Do not repair a damaged

cable, replace it with a new one. Use only genuine

replacement cable.

9. Keep long hair away from air inlet.

10.Keep all inlets clear of debris.

11.Always remain alert.

9. Never carry the product by the cable.

10.Never pull on the cable to disconnect any of the plugs

11.Always wind cable carefully, avoiding kinking.

12.Use only on AC mains supply voltage shown on the

product rating label.

12.Do not attempt to use your product without the fully

assembled debris bag fitted.

13.Never blow debris in the direction of bystanders.

14.Do not overreach. Keep proper footing and balance

at all times.

13.Our products are double insulated to EN60335.

Under no circumstance should an earth be con-

nected to any part of the product.

15.The impeller continues to rotate after your product

has been switched off.

16.Remove the plug from the mains :-

Preparation

before removing or replacing fully assembled debris

bag;

1. While using your product always wear substantial

footwear and long trousers.

before leaving the product unattended for any period;

before clearing a blockage;

2. The use of eye protection is recommended.

3. The use of ear protection is recommended.

4. To prevent dust irritation, the wearing of a face mask

is recommended.

before checking, cleaning or working on the product;

if the product starts to vibrate abnormally. Check im-

mediately. Excessive vibration can cause injury.

Maintenance and storage

5. Do not wear loose clothing or jewellery that can be

drawn into the air inlet.

1. Keep all nuts, bolts and screws tight to be sure the

6. Do not wear clothing with attachments, i.e. toggles or

drawstrings that can be drawn into the air inlet.

7. Inspect your product before each use.

8. Do not use if any part is damaged or broken or if any

of the screws are loose. Have it repaired by an au-

thorised repairer.

product is in a safe working condition.

2. Replace worn or damaged parts for safety.

3. Use only genuine replacement parts and accessories

4. Inspect the debris bag regularly. If the debris bag be-

comes worn or damaged, replace.

5. Store in a cool dry place and out of reach of children.

Do not store outdoors.

9. Always check your product is in a safe operating

CABLES

IMPORTANT

cut off plug is inserted into a 13 amp socket.

1. No earth required. Flymo products are double

insulated to EN60335 and under no circum-

stances should an earth be connected to any

part of the product.

•

Use only 1.00mm size cable up to 40 metres

length maximum.

Maximum rating :

1.00mm size cable, 10 amps 250 volts AC.

2. Ensure the mains voltage suits your product

3. IMPORTANT!

•

YOUR PRODUCT IS SUPPLIED WITH CABLE

WIRED DIRECTLY INTO THE PRODUCT.

The wires in the mains lead are coloured in ac-

cordance with the following code:

1. Flymo Mains Cables and Extension Cables are

available from your local Approved Service Centre.

2. Do not wire an extension cable directly to your

product yourself. Please contact your local Ap-

proved Service Centre for further information on

the connectors and kits available.

BLUE

NEUTRAL

LIVE

BROWN

The wire which is coloured BLUE must be con-

nected to the Terminal which is marked with the

letter 'N' or coloured BLACK.

3. Only use extension cables specifically designed

for outdoor use.

The wire which is coloured BROWN must be

connected to the Terminal which is marked with

the letter 'L' or coloured RED.

CONNECTORS

IMPORTANT

4. It is important that the outer sheath is clamped

correctly into the 3-pin plug.

•

Flymo connectors are suitable for use with 2 core

cable only. Under no circumstances should these

connectors be used for earthed products.

All Flymo connectors and cables are of splashproof

construction. They are not waterproof and must not

be left outside permanently nor should they be sub-

merged or immersed in water. Do not let cable lay or

trail through pools of water or splashed with water

from hose pipes.

5. If in doubt consult your local Service Repairer or

qualified electrician before the machine is used.

6. A 13 Amp fuse must be fitted to the Mains Plug.

7. The normal plug fuse and household fuse only

protect the electrical equipment and are not a

safeguard against electrocution.

•

If the mains cable is damaged, it must be re-

placed with the correct Flymo assembly from an

Flymo Approved Service Dealer (see leaflet en-

closed in product)

MAINS PLUG REPLACEMENT

IMPORTANT

If the plug supplied is cut off it should be de-

stroyed. There is an electric shock hazard if a

•

Blow Tube & Shoulder Harness Assembly

Blow Tube Assembly

Shoulder Harness Assembly

1. Attach the blow tube to the product as shown in Fig

1. Attach the Shoulder Harness to the product as illustrated in Fig B.

2. Adjust the Shoulder Harness as required to ensure it is in

the most comfortable position. (C).

A, ensuring it clicks securely into position.

Suction Tube Assembly

1. Attach the two Suction Tube halves together as illus-

trated in Pic D. Ensure that the two halves click se-

curely into position.

IMPORTANT

When the Suction Tube halves are attached together,

this is a permanent fixture, they can not be disassem-

bled.

Converting from Blower to Suction

1. Turn the product over and press the release catch on

2. Slide the catch away from the product (E2) and re-

move the Blow Tube from the product (E3).

the Blow Tube (E1).

3. Press the release catch on the Impeller Guard (F1).

4. Release the wire hook (F2).

5. Turn the Impeller Guard anti-clockwise until it can be

removed (F3).

6. Attach the assembled Suction Tube to the product

aligning the arrows as indicated (G1).

7. Turn the Suction Tube until it clicks into position (G2).

8. Secure the wire hook into postion and close the catch

(G3).

9. Place the loop on the Debris Bag over the end of

the Suction Tube (H1)

10.Attach the Debris Bag inlet to the product as

shown in Pic H2, ensuring that it clicks securely

into position. (H3)